I just got my winch in and wanted to install it tonight. I was wondering what the best route is to go with this. Should I use the Two plug method if so how would I go about doing this. Or should I just use the one plug. If really like to only use one battery. But I suppose I could use a small nimh hump pack for this one. Any help is greatly appreciated.
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
3Racing winch wiring HELP
- Thread starter OH6HEMI
- Start date
SirKarnage
Rock Stacker
I clipped the battery connector off and soldered those wires inline with the ESC power wires. plug in battery, good to go.
It's a 2s so it's good. But i have a tf40 tx on this one and when I plug the winch in it just spools by its self I think I have it hooked up wrong or sonething. Is this right?http://img.tapatalk.com/d/14/01/09/
u3ysu6a8.jpg
I cut the tamiya connector off and soldered like that. I see what the problem is now that I thought about it. It's constantly getting power but how am I supposed to correct this?
DRIVNMF
I wanna be Dave
My favorite mod to run the 3R winch is use a second ESC as the winch controller.
I run a 3S lipo to mine. The motor takes it like a champ. The two main reasons why I use an ESC for this purpose;
One, I use a MT4 radio. The lever is my winch control. I have a variable speed line rate.
Two, when I do not need my winch, I turn the ESC off and never have to worry about line creep.
There are several great ways to wire your winch up. This is what works best for me. Remember when winching, use the Official Land Anchor of the RECON G6, the Pul Pall RW60. Don't get stuck without one! "thumbsup"
stevetate12
Quarry Creeper
this is exactly what I did.....and mine works great too.....
Sent from a big fat phone
jmz6
Rock Crawler
Fixed the link for you
It's a 2s so it's good. But i have a tf40 tx on this one and when I plug the winch in it just spools by its self I think I have it hooked up wrong or sonething. Is this right?
It works fine on channel 1 or 2 but if you put it on channel3 the winch just spools with me pressing anything. I don't understand this. Has anyone else had this problem or is it just me?
SirKarnage
Rock Stacker
Is the trim on 3 set correctly? I had the issue at first as well. My radio, the DX3R, 3rd channel had to be switched in the programming to 3way position and then my trim was off. Once centered it works fine. But yes mine is wired as in the pic above
Sent via Pocket Command
Sent via Pocket Command
Mine is a push button 3 channel on the tf-40. I think it's my radio being a push button. Does anyone know I good reliable SIMPLE 3 channel 3 position radio so I can use this damn winch?
Noll11
What could go wrong?
For much cheaper than a new radio you can get this and wire it in.
http://www.rccrawler.com/forum/vend...dio-2-position-third-channel.html#post2802735
Planning on getting one myself soon so I can use my servo winch with my 2pos 3ch radio.
http://www.rccrawler.com/forum/vend...dio-2-position-third-channel.html#post2802735
Planning on getting one myself soon so I can use my servo winch with my 2pos 3ch radio.
Yeah but it's so much easier just to have the remote. I wanted a new one anyway. "thumbsup" I'll probably end up getting a heyok anyway.
Noll11
What could go wrong?
Makes sense 
.
.SirKarnage
Rock Stacker
To me it still just sounds like the settings on your third channel. I don't know your radio, at all, but find someone that does, and get it worked out.
unless you really really want a new radio...
Like I mentioned, the DX3R has 2pos, 3pos, and others available for each channel, yours is probably just set in one of the others.
Similar threads
