What is the recommended shifter servo to use ;-)
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
AX2 2 Speed Transmission for Axial Wraith & SCX10/Honcho
- Thread starter Racer4Life
- Start date
What is the recommended shifter servo to use ;-)
RKSTAR
Quarry Creeper
Man I want one when are they going to be back in stock anywhere?
TrailDawg362
RCC Addict
I got mine from CKRC, since everyone else was out. For shifter servos, just about anything will work. Standard size and torque units will have no problem moving the shift rod. One of the mini sized servos should be just fine also.
Rockridge
Quarry Creeper
I use a Hitec HS65MG mico servo with a servo saver
RKSTAR
Quarry Creeper
Back in stock....yea!
Racer4Life
I wanna be Dave
I have not heard of any failures on these units. I think we had 1 or 2 break the shift rod.
Pabust
Quarry Creeper
Here's a friend's Wraith with the Pro4 3300 on 3S and the AX2 trans:
<iframe width="560" height="315" src="http://www.youtube.com/embed/yk4QwsHamFs" frameborder="0" allowfullscreen></iframe>
<iframe width="560" height="315" src="http://www.youtube.com/embed/yk4QwsHamFs" frameborder="0" allowfullscreen></iframe>
Is that stripping sound the spur gear or just normal sound of the transmission
Jeepfixer1
Rock Crawler
I just listened to this and I'm not sure what that is. I have had one of these since it first came out and still love it. I have been using the mmp/pro4 3300 since I installed it. I have also ran it on 3s the whole time to. Nothing on the trans has broke. I did strip one ft diff standard ring and pinion and the slipper clutch has backed off once. The slash slipper would be a reccomended upgrade however I haven't swapped in one yet! The trans in my book gets an A+. The trans Along with the Tekin pro 4 are the best two single mods that I have made.
I think I'm going to try one. Did you do any upgrades to the trans.
YJ_Driver
Quarry Creeper
I had some grit get into the pinion/spur once and it made a nasty noise. I cleaned it out and it was quiet again and there was no damage. So if anyone makes a gear cover for this unit I'll buy one ;-)
Jeepfixer1
Rock Crawler
No i didn't do any upgrades to the trans other than more grease when i first got it. Als you can modify the stock spur gear cover to work. I show how to earlier in this thread! Im running mine and works great.
Crawlorado
Newbie
Can these run the super shafty beefy top shafts? If not, how are you guys running your 32p Robinson spurs?
I doubt that shaft will work. But as many have said, it pretty strong. I run mine with a pro4 on 3s. My only complaint would be the threaded shift shaft. It is not locked in to place & rotates during use. To the point that the linkage block fell off the shaft. I recommend red locktite to keep it from unthreading.
Pabust
Quarry Creeper
X2 on the shift shaft, they would want to rethink that design, mine has fallen apart twice
Another very happy customer here:mrgreen:
Apart from the shift linkage issue already mentioned its great. I have mine in a bruiser running a 25t HH motor on 3s and low range is awesome, heaps of reduction but hi range is even better 8)
Ill be ordering another for other rigs definitely:mrgreen:
Apart from the shift linkage issue already mentioned its great. I have mine in a bruiser running a 25t HH motor on 3s and low range is awesome, heaps of reduction but hi range is even better 8)
Ill be ordering another for other rigs definitely:mrgreen:
Super
Rock Crawler
Just got mine today.
Working on installing it now."thumbsup"
Working on installing it now."thumbsup"darkwolf131313
Newbie
will this transmission work with the dual motor mount by level 3?
