What splice thing? if you are talking about the plug that goes into the RX and has a wire coming out and looping back to the plug that is just the bind plug and can be removed
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
GT3B Hack Question and Answer Thread
- Thread starter losikid
- Start date
What splice thing? if you are talking about the plug that goes into the RX and has a wire coming out and looping back to the plug that is just the bind plug and can be removed
Natedog
I wanna be Dave
That's part of the antenna, you need it. "thumbsup"
losikid
Got Worms?
That "splice" is the antenna...the antenna on the v2 6 and 8 ch rxs use a real dipole antenna. Which will give more range and a better connection...other radios and the v1 rxs uses a satellite antenna (a small rx plugs into big one). You probably could replace it with the standard 2.4 coax cable. But I haven't tried.
losikid
Got Worms?
it depends, I haven't looked inside a v1 rx for along time. it isn't too hard on the v2 6 ch rx, I've had to solder mine back on afew times...the tx module side through is a huge pita. as you have a solder pad that's less than .050" square, and real close to the other.
but you should still have 10-20+ ft of range with no antenna. and just plug in your satellite, it should give you plenty of range.
hobbypartz does sell v1 rx. its branded as exceed...but these DON'T WORK WITH THE GT3B, I you know this, probably, but don't want others think it will bind up.
losikid
Got Worms?
I think I misread your question, great thing about a smart phone, where did you pull the antenna loose?
JokersWild
RCC Addict
Mines all loaded up and fine.
anyone ran it with 4ws yet? Trying to figure if i can set up channel 3 for 3 positions as in (front wheels steer, crab, then both axles turn the same)
if not then Ill have to figure out the 3 positions of left, center, right (which i have set in muti position as -100(left turn) 0 100(right turn) but after i save it.... no workie workie.)
anyone ran it with 4ws yet? Trying to figure if i can set up channel 3 for 3 positions as in (front wheels steer, crab, then both axles turn the same)
if not then Ill have to figure out the 3 positions of left, center, right (which i have set in muti position as -100(left turn) 0 100(right turn) but after i save it.... no workie workie.)
JokersWild
RCC Addict
Im thinking out of the board of the receiver. just solder it back in?
losikid
Got Worms?
Currently 4 ws works with the trim switches or d/r. it can do front, mix, rear for crab you have to program the ch 3 button, or other button, to go in and out of crab.
multi position is for the buttons, like the ch 3 button, this is probably your problem
losikid
Got Worms?
So you put v2 modules in your t6a?
but yes, v2 tx modules are a pita to solder back on, but possible, I've done it quite afew times
but yes, v2 tx modules are a pita to solder back on, but possible, I've done it quite afew times
losikid
Got Worms?
I'll look at this no save problem Monday evening when I get back home, and answer questions better when I have a real key board. that doesn't have a bad digitizer.
JokersWild
RCC Addict
No worries. I dont need it to work now. Just trying to make heads or tails of how to move the channels to each button and how to make that all work for the 4ws. Somewhere im overlooking something.... :lmao:
