How to set-up screen on all the time and the inactivity alarm?
Thanx!
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
GT3B Hack Question and Answer Thread
- Thread starter losikid
- Start date
Thanx!
losikid
Got Worms?
Who'd be interested in programming cards? To go in your wallet or rc box.
So it'll have afew tutorials, 3 pos switch, Multi postion switch, dual esc, 4ws, and then a shortcut quick card, so you can look and see what the abbrevs on the radio mean.
Also, paper biz card? nearly free
Thin plastic card? Cheap
thick plastic card (like a CC)? abit pricy
On another note, i plan on finishing up key mapping menu and writing tutorials this week....probably get to work on the rest of the manual. Still waiting on afew more hack kit orders to get some VR's in.
So it'll have afew tutorials, 3 pos switch, Multi postion switch, dual esc, 4ws, and then a shortcut quick card, so you can look and see what the abbrevs on the radio mean.
Also, paper biz card? nearly free
Thin plastic card? Cheap
thick plastic card (like a CC)? abit pricy
On another note, i plan on finishing up key mapping menu and writing tutorials this week....probably get to work on the rest of the manual. Still waiting on afew more hack kit orders to get some VR's in.
losikid
Got Worms?
Have you referenced the manual?
here is the snippet you'd be using, this ALOT simpler than key mapping
Code:
Global setup menu:
==================
- enter it by ENTER-long
- now menu items MODEL and NAME will start blinking
- select requested item by ROTATE and press ENTER
- use ROTATE to change value and press ENTER to end value changing
- press BACK-long or ENTER-long to end global setup menu,
values will be saved to EEPROM
- selected menu items are indicated by following symbols:
F firmware version (this of course cannot be changed :-)
L backlight time 5s,10s...10m...MAX
A inactivity alarm OFF,1m...10m
LOW POWER! battery low voltage 7.5...10.5V
E.POINT maximum allowed endpoint value 100...150%
DANGER - values greater than 120% can damage
your servo or will not be possible
to transmit to receiver because of
2.4GHz HF module limitation
This danger zone will be indicated with a flashing "d" symbol
for values greater than 120%
1 dead zone for steering 0...50
2 dead zone for throttle 0...50
b key beep OFF/ON
d long press key delay 100...1000 miliseconds
r + ALL global reset - change to YES to set global configuration
and all models to default values
r + MOD all models reset - change to YES to set all models
to default valuesCan you help me to fihure it out.
because i am still dont really understand after read the manual.
it's because my english not very good.
i already translate it with google translate:mrgreen: but steel confuse.
I just ordered the hack from Losi kid and am awaiting the radio from Hobbypartz. I have been looking at a lot of this and to be honest I think I am over thinking this some but why not right! I have a few questions as I get ready to go.
1 There appears to be a computer card in the $25 hack kit that is one the way to me. What is that for?
2. I noticed it looks like this is a three step process to get up and running. 1.is get the pins installed. No brainer. 2. is to plug it into the computer and flash it. Also looks easy. 3. It appears that you have to reprogram all your calibrations on the radio? Is this right?
I am still hoping I can use this radio with the flash to program the amount of throw at right and left steering with right and left independant of each other. I am also wanting to be able to program throttle amount for a 5 year old with a slash!! I am super excited about this so thanks Losi kid.
RickM
1 There appears to be a computer card in the $25 hack kit that is one the way to me. What is that for?
2. I noticed it looks like this is a three step process to get up and running. 1.is get the pins installed. No brainer. 2. is to plug it into the computer and flash it. Also looks easy. 3. It appears that you have to reprogram all your calibrations on the radio? Is this right?
I am still hoping I can use this radio with the flash to program the amount of throw at right and left steering with right and left independant of each other. I am also wanting to be able to program throttle amount for a 5 year old with a slash!! I am super excited about this so thanks Losi kid.
RickM
losikid
Got Worms?
The computer card is the programmer...it plugs into the computer, and the radio plugs into the card.
your steps seem right
yes epa is independent, and its available for all channels.
highlandcrawler
Rock Crawler
Hope that helps a little
EDIT: Hes a fast typer also
Tuning down the steering speed might help me with my newish 4wd slash! If this radio flash etc is as cool as the wantasummit 3pos switch and the was duel esc thingy, than count me as a fan already. I am not the greatest with electronic stuff as the details are my demons but I know I will eventually get it right and to be honest right now I am only worried about this as a 2 channel radio for an MRC and a slash. I might be ditching my 4pl if this is as good as it sounds though.
losikid
Got Worms?
Yea i'd say this is much cooler than the wAs adapters...because a.) its uber cheap, and b.) if you flashed it, you have self satisfaction knowing you turned a turd into a gold nugget.
And it is abit confusing at first how to program it, but its much easier once you understand how.
Hi All,
just to say that I have received the gt3b hacked by losikid yesterday, he does the job and the shipping very quickly. Once received I went to the post about how to set up the dual esc, 5 minutes later my berg was running ...dig and prop. dig are great ! "thumbsup"
Thank you very much Losikid, you've done a great work "thumbsup""thumbsup""thumbsup"
just to say that I have received the gt3b hacked by losikid yesterday, he does the job and the shipping very quickly. Once received I went to the post about how to set up the dual esc, 5 minutes later my berg was running ...dig and prop. dig are great ! "thumbsup"
Thank you very much Losikid, you've done a great work "thumbsup""thumbsup""thumbsup"
please help.:sad:
losikid
Got Worms?
Ok this is off the top of my head
DIG to Ch3 trim (rx CH 3)
4WS to D/R switch (rx CH4)
Winch to ST trim (rx CH5)
Crab to ch3 Button
Scroll to EPA
Press and hold enter
scroll to d
press enter
scroll to 3 press enter
scroll to 0,
press enter
scroll to 4
press enter
scroll to 4 press enter
scroll to 0
press enter
scroll to NOC press enter
press and hold enter
Scroll to REV
press and hold enter
scroll to 3
press enter
scroll to DIG
press enter
scroll to RES
press enter
scroll to 100
press enter
scroll to NOR
press enter
scroll to NOO
press enter
scroll to d
press enter
scroll to 4ws
press enter
scroll to RES
press enter
scroll to 100
press enter
scroll to NOR
press enter
scroll to NOO
press enter
scroll to 1
press enter
scroll to CH5
press enter
scroll to RES
press enter
scroll to 100
press enter
scroll to NOR
press enter
scroll to NOO
press enter
scroll to C
press enter
scroll to 4ws
press enter
scroll to SWI
press enter
scroll to NOR
press enter
scroll to NPV
press enter
press and hold enter
press back
losikid
Got Worms?
So i woke up this morning and my computer had restarted...didn't think much about it
Well i just went to go convert the finished key mapping manual over to a pdf and let ya'll take a look. But i lost it all,
I had the buttons menu done and had abunch of templates/tutorials written
:evil:
So it may be awhile before i write it all again,
Well i just went to go convert the finished key mapping manual over to a pdf and let ya'll take a look. But i lost it all,
I had the buttons menu done and had abunch of templates/tutorials written
:evil:
So it may be awhile before i write it all again,
losikid
Got Worms?
I do have good news though....i have Voltage Regulators ordered, so they should start shipping next week...there will be 9 in stock after pre-orders have been sent out.
My next project is adding a bearing to the st wheel to make it buttery smooth. .
After that it'll probably be adding/moving switches.
My next project is adding a bearing to the st wheel to make it buttery smooth. .
After that it'll probably be adding/moving switches.
JokersWild
RCC Addict
"thumbsup""thumbsup" Sweet.. Ill be on getting some bearings for the wheel!!
losikid
Got Worms?
It'll be awhile...maybe.
After my order this morning, i have no money. So i'd like to run through a batch of kits and refill my pillow to cushion any unexpected stuff.
Well I mentioned I am not great with electrical stuff but this might sum it all up. I just got the stock GT3B in today and am waiting on the flash kit. I decided to try and go ahead and hook up the radio to my kids mrc. Well in doing so I am having a hard time getting my sidewinder micro esc to arm and communicate with the RX. I have bound it and my servo is working. It is getting its power off the battery anyway. I got my esc to start to chime and then it immediately starts flashing red. I tried to fire it up with my throttle in full gas mode but it keeps doing the same thing. I tried to trouble shoot it with Castle and they did not say much in the trouble shooting stuff. I double checked to make sure I am plugging everything in right and from what I can tell I do. Any ideas?
losikid
Got Worms?
Try reversing the channel...then calibrate the esc
