Jcplante
Rock Crawler
^ mine does the same and its not hacked.
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
GT3B Hack Question and Answer Thread
- Thread starter losikid
- Start date
JokersWild
RCC Addict
Have either of you calibrated your ecs and or checked settings in esc?
sriederer1
Newbie
Why is it so hard to get one of these radios from overkill RC? I have received two emails and right away it says out of stock?
losikid
Got Worms?
Probably because they are in high demand and people buy them within a couple days of being posted"thumbsup"
I'll have 20 more going to be posted in a week or so. I need to get all the current orders built/packed/shipped before I can take anymore orders.
Hacked GT3B, version 6 I believe. Has completely stopped controlling ch1, I can still adjust the servo with the trim, but I have no steering function. I have swapped in a steering potentiometer from a known working un hacked unit with no change and I have tested the servo on a completely different system and it works as desired. It would seem to me that the channel on the board has failed, any thoughts?
tgraceing
Newbie
have you tried new receiver, if not try that first they can and do fail.
rockhugger
RCC Addict
I've got two questions regarding programming a hacked 3c.
In the manual for 0.6.1 in the global setup menu items there is an option to make Ch3 a potentiometer, what applications would this be used in?
How would I set up rear steer to be incremental on Ch3, with long press to center, otherwise short press is incremental in either dir. to go like this (my thoughts are multi pos switch, but not sure) :
L >25-50-75-100- long press in the other dir. to center _ R >25-50-75-100- long press in the other dir. to center
with C as Crab - NoCrab option ?
I hope that makes sense.
Thank you in advance.
In the manual for 0.6.1 in the global setup menu items there is an option to make Ch3 a potentiometer, what applications would this be used in?
How would I set up rear steer to be incremental on Ch3, with long press to center, otherwise short press is incremental in either dir. to go like this (my thoughts are multi pos switch, but not sure) :
L >25-50-75-100- long press in the other dir. to center _ R >25-50-75-100- long press in the other dir. to center
with C as Crab - NoCrab option ?
I hope that makes sense.
Thank you in advance.
Last edited:
rockhugger
RCC Addict
I think this is pretty much what I'm looking for, but I am not sure how to set it up. "thumbsup"
JokersWild
RCC Addict
I got ya brother......... Let me check my set up. Btw you should like it at 20%
Last edited:
JokersWild
RCC Addict
Obviously you got your channel to switch set up.... I run my winch on the d/r switch and rear steer on the ch3 trim. Using 6ch rx. So here we go........
Long hold on rev.
3 ch4
3 bnl
3 20v
3 re 0
3 ro 0
Then save it all up by pressing end etc etc.
Now if ya don't like how it holds each % and to move from 10-20 you have to tap tap tap to get to 100% swap out the bnl to bar and step the 20v down to 10v...... Try each and see how ya like it. Now on first set up if you want back center you just center push the button straight in and will auto to 0%........ Let me know how it goes eh.
I'm stuck between both set ups right now. Lol both have ups and both have downs.
Long hold on rev.
3 ch4
3 bnl
3 20v
3 re 0
3 ro 0
Then save it all up by pressing end etc etc.
Now if ya don't like how it holds each % and to move from 10-20 you have to tap tap tap to get to 100% swap out the bnl to bar and step the 20v down to 10v...... Try each and see how ya like it. Now on first set up if you want back center you just center push the button straight in and will auto to 0%........ Let me know how it goes eh.
I'm stuck between both set ups right now. Lol both have ups and both have downs.
Last edited:
JokersWild
RCC Addict
So you are saying you screwed up you own radio but its all fine now? Lol
Glad its working for ya now."thumbsup"
rockhugger
RCC Addict
Awesome, I'll give this setup a try... it seems so easy when you break it down like that. I'm still trying to learn the basics of the radios language. "thumbsup"
thank you
JokersWild
RCC Addict
No problemo, let me know how it goes and what one you liked.
rockhugger
RCC Addict
the scroll wheel button just died because when I press it nothing happens, has this happened to anyone else?
Last edited:
Yes. My radio came like that. Would only work 1 out of 200 presses. I opened up the radio. Pryed the top of the switch open. Bent the metal plate inside the switch so when the button was pushed it made contact completing the circuit. I will explained better in a couple hours my daughter is demanding my time right now.
losikid
Got Worms?
Ok, I would have swore someone posted a question in the past page or so about how to do multi position...I was rather excited to answer because I haven't had that question for a long time and I feel like it is so far out of the norm people don't realize it's there and it's not used very often.
Was I dreaming this up? Or did this post get deleted?
Was I dreaming this up? Or did this post get deleted?
losikid
Got Worms?
And I'm gonna need to look into this enter button issue....I haven't been able "break" any of the ones I have here. I've done 500-1000 enter button presses on 3 different new radios....can't get one to break so I can diagnose the cause.
Are you guys' still getting the tactile "click" when you press the enter button and get no response?
Are you guys' still getting the tactile "click" when you press the enter button and get no response?
