Wraith/AX10/SCX10 pinion bearing mod

[Erik D_lux]

Just placed an order for 2 Wraith housings. Are there any SCX housings left? I would like 4. I'm building a 6x6.

I dont have any SCX housings right now, I keep just a small stock on them since they dont seem to be as popular.

If you would like 4 housings, I should have them ready in just a couple of weeks. Let me know and we can arrange a pre payment and that way it can ensure you get all 4.

Erik, any chance of sending you 4 housings and having the mod done to them?

Also is it a 5x13x5 bearing or a 5x13x4?

I am sending a PM now...

 

[65BAJA]

Ok, I read the PM before this post. Yes, it would be for 4 stock SCX housings cut for the big inner bearing.

 

[Erik D_lux]

All housings in stock including a few SCX. "thumbsup"

 

[Wizardman]

Just ordered a set :thumbsup:

Sent from my HTC6435LVW using Tapatalk

 

[Erik D_lux]

Thanks!

Shipping now!

 

[stelerzman]

Does this mod still require the pinion to be shimmed? If so, does anyone know how much? Thanks.:mrgreen:

 

[winnerone23]

Nope! The mod is actually done to leave a little extra meat behind the bearing. Which keeps it spaced out and gear mesh is perfect!

I run the Dlux modded product on my Sexo, scx and yeti... All pushing 4s brushless power!

 

[Erik D_lux]

It all depends on what gear ratio you run. I leave a hair more material for a good tight mesh on a standard ratio. Under drive will be a bit tight and over drive will be sloppy. So, if you have over drive, which is usually a bad idea, you will probably want to shim it a touch. If I remember right I think it was .020" or .5mm?

 

[stelerzman]

Nope! The mod is actually done to leave a little extra meat behind the bearing. Which keeps it spaced out and gear mesh is perfect!

I run the Dlux modded product on my Sexo, scx and yeti... All pushing 4s brushless power!

It all depends on what gear ratio you run. I leave a hair more material for a good tight mesh on a standard ratio. Under drive will be a bit tight and over drive will be sloppy. So, if you have over drive, which is usually a bad idea, you will probably want to shim it a touch. If I remember right I think it was .020" or .5mm?

Thanks guys, I normally run over in the front and stock in the rear. I do have shims so it won't be an issue. I just got them today so I'll get building tonight.
Thanks Erik, I really appreciate everything."thumbsup"

 

[Erik D_lux]

Sorry for the long wait. I now have EXO/Yeti bulk heads back in stock.

 

[DickyT]

Order placed, thanks for making these great products for us Erik!

 

[84yoda]

Any idea when you will have more ar60 housing?

 

[Erik D_lux]

They are still in stock.

 

[84yoda]

On ur site, it says ar60 wraith bearing mod is out of stock?

 

[Erik D_lux]

It should show 37 in stock. Make sure youre not looking at the AX10/SCX10 housings. I am out of those and they will say out of stock.

 

[84yoda]

I am 110% positively looking at ar60... if i could post a screen shot i would to show it

 

[84yoda]

Ar60 with bigger bearing or thrust washers?

 

[ninja turtle]

I am 110% positively looking at ar60... if i could post a screen shot i would to show it

You are doing something wrong. Try again.

 

[Erik D_lux]

Please do post a screen shot. Here is mine.

 

[84yoda]

Wtf... i went to axles then sub category wraith and it shows out of stock, i promise u.. i wouldn't waste my mind right now if it wasnt out of stock..