simpley one of the coolest builds iv'e seen yet. can"t wate to see what ya do with paint"thumbsup" GSRCC Drail |
looks funkin evil man! I think the choice on taking the windshield tube out was the right one. can't wait to see it done up! |
Now that looks good. I think what was said was not to remove the windshield brace, but not to have it overlap the frame brace and make it a V rather than a single piece. But it looks sick. cant wait to see it done. "thumbsup" |
Quote:
|
Quote:
Quote:
Quote:
Quote:
|
Quote:
|
Proline, Discontinued body part number pro3148-00 if I could find someone who actually had one, Id buy it |
i see the differences now. i'll check in the massive pile of bodies at the hobby store when i pick up my parts Thurs or Fri |
|
Thanks for the help guys, I have a few emails out to these place to see if they actually have them or not.. Playing around with the idea of a light bar, not exactly what I would use, just getting an idea. could go either way.. http://i1148.photobucket.com/albums/...c/DSC07162.jpg |
what about the RPM SC 4 light bar? looks SICK man! |
Andy another thought on the light bar is to "sink" it into the headache bar kinda like Tim did on the Gaineys truck. It would lower that line a bit and might work to add the V brace on the windshield then? |
or how about a fold down bar that could fold down onto the dash, to better protect it. like in-board police spotlights haha! |
yeah, jury is still out on the light bar, i'll think of something though... |
I got your resolve. put this on it instead and become a recovery vehicle. http://cgi.ebay.com/ws/eBayISAPI.dll...=STRK:MEWAX:IT will the summit light bar fit on there and you can make a low profile bar to go over it and protect it. http://cgi.ebay.com/TRAXXAS-SUMMIT-L...item335b55b576 these cop lightbars ones are 3 inches long and take 3mm lights nicely. I used one like it on my RC18 cop car. http://cgi.ebay.com/1-18-SCALE-WHELA...item563c28c01c http://i265.photobucket.com/albums/i...e/IMG_1783.jpg |
cop lights are out... But I did think of something like the summit bar, I need to figure it out soon. |
figured out what I am going to do for the light bar, need to track down 2 or 3 of the smaller light buckets and lenses from the honcho kit first. ( I could but the light kits but I only need the small ones...) so that will need t wait a few more days. tonight I worked on the fun part, making everything fit. Started with a battery mount, just a simple mount I made out of a scrap piece of kydex sheet. I needed something that could hold 2,3 and 4s batteries. http://i1148.photobucket.com/albums/...c/DSC07169.jpg with a 4s batt installed ( I have 2 and 3s packs of the same size that fit in here as well. ) http://i1148.photobucket.com/albums/...c/DSC07164.jpg packed under the hood tight http://i1148.photobucket.com/albums/...c/DSC07166.jpg Then I moved on to trying to find a place for the winch servo, after some head scratching it looks like this will work, Ill have to route the line under the truck, probably through a tube of some sort, but its in there. http://i1148.photobucket.com/albums/...c/DSC07172.jpg http://i1148.photobucket.com/albums/...c/DSC07174.jpg I need to finish up the mount for the winch servo, get the esc and rx in there, mount the rear winch, get the lightbar on, get the interior worked out, then its time for paint. Oh and I need to find stiffer springs, this thing is turning into a pig! |
Good idea on the servo winch placement. I had my 4s 2100 in the same spot on the Pirate 4x4. Once I put my winch in best I can fit up there is a 4s 1350. :cry: I have to ether run it in the back or try what you did. Thanks "thumbsup" |
This thing is dead sexy. |
Looks good man. Send me you addy and Ill send ya the 2 small axial lights I have. |
All times are GMT -6. The time now is 08:51 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com