01-13-2009, 06:12 PM | #1 |
Rock Crawler Join Date: Jan 2006 Location: Phoenix
Posts: 573
| GTG Saturday Jan 17th
GTG at New Papago Saturday say 9 am ish , doing this on saturday to avoid the playoffs on sunday (GO STEELERS) Who is in? I need to try out my newmotor setup before the first comp, and the wintershoot out the following week |
Sponsored Links | |
01-13-2009, 08:55 PM | #2 |
I wanna be Dave Join Date: Sep 2007 Location: San Tan Valley
Posts: 4,267
|
I'm down...I've got to try out my new MRC and get ready for the winter shoot out.
|
01-13-2009, 09:23 PM | #3 |
Rock Crawler Join Date: Jan 2006 Location: Phoenix
Posts: 573
|
LOL knew you couldn't resist the dark side.
|
01-13-2009, 09:58 PM | #4 |
Rock Crawler Join Date: Aug 2007 Location: mesa az
Posts: 657
| |
01-13-2009, 10:29 PM | #5 |
Quarry Creeper Join Date: Sep 2006 Location: Phoenix
Posts: 477
|
I'm in. I need a TON of stick time with the new 2.2 and I ain't got any the last two weekends.
|
01-14-2009, 04:15 PM | #6 |
Rock Crawler Join Date: Dec 2007 Location: GILBERT
Posts: 751
|
so since we have so many minis does any one know what the rules are?
|
01-14-2009, 05:08 PM | #7 |
I wanna be Dave Join Date: Sep 2007 Location: San Tan Valley
Posts: 4,267
| |
01-14-2009, 05:25 PM | #8 |
Rock Crawler Join Date: Jan 2006 Location: Phoenix
Posts: 573
| 2.1.2.2 – 1.9 Class body must be 2.75” minimum height on sides. No less than 9” total length and full original width, and no less than 3” in the center. All bodies should resemble its original form (Jeep bodies look like a Jeep) 2.1.3.5 - 1.9 class minimum overall bodiless dimensions must be 6.75” overall length, 2.5” overall width, & 3.25” overall height. Class 3 – Class 1.9 : If a Class 3 vehicle violates any of the following requirements it must run in Class 2 or Class 1 respectively. • 2.4.1 - Vehicle wheelbase is limited to a maximum of 8.5 inches. This is determined by measuring from centerline of front axle stub to centerline of rear axle stub, with all the wheels pointing straight ahead, with the vehicles suspension holding it's own weight. • 2.4.2 - Vehicle track width is limited to a maximum of 8 inches. This is determined by measuring the bottom of the outer most edge of the front and rear tires while the vehicle is sitting on level ground. • 2.4.3 - Vehicle is limited to 1.9 inch wheels/rims or smaller at the bead surface. Wheels may be modified provided that the tire bead surface does not exceed 1.9 inches in diameter. Tires may be modified from other sized tires using only a pliable rubber but must not exceed a total uncompressed outer diameter of 4.25 inches. • 2.4.4 - Vehicles are limited to 2-wheel steering on front axle only. • 2.4.5 - Vehicles are limited to the use of 2 channels radio control (one for steering & one for throttle) only. Neither channel can be used to perform more than one function. Radio systems with more than 2 channels are allowed but only 2 channels can be used to control the vehicle. • 2.4.6 - Vehicles are limited to 1 ESC & 1 servo only. 4 • 2.4.7 - Vehicles are limited to 1 motor powering both of the axles. • 2.4.8 – No driver controlled devices, other than steering and throttle control, will be allowed. Independent throttle control to the front or rear axles (“burn” or “dig”), winching down the axles, and forced articulation are not allowed in this class. • 2.4.9 – A battery is limited to 8.4 nominal voltage (7 cell nimh/nicd & 2 cell lipo/limoly). • 2.4.10 – 1.9 Crawler class bodiless overall dimension of the complete chassis must be at least 6.75" overall length, 2.5" overall width, and 3.25" overall height. • 2.4.11 - If at any point during a run your vehicle falls out of these vehicle specs for any reason you will be required to take a touch penalty and correct the problem. There ya go |
01-14-2009, 05:51 PM | #9 | |
I wanna be Dave Join Date: Sep 2007 Location: San Tan Valley
Posts: 4,267
|
Sweet...That works!...But I still like my answer better! Quote:
| |
01-14-2009, 06:06 PM | #10 |
Rock Crawler Join Date: Jan 2006 Location: Phoenix
Posts: 573
|
LOL, You must have stole it cuz you didn't get it from us |
01-14-2009, 07:48 PM | #11 |
I wanna be Dave Join Date: Sep 2007 Location: San Tan Valley
Posts: 4,267
| |
01-14-2009, 08:10 PM | #12 | |
Quarry Creeper Join Date: Sep 2006 Location: Phoenix
Posts: 477
|
...and gates are 12 inches. Read that in the official rules on this site. Quote:
| |
01-14-2009, 11:59 PM | #13 |
Rock Crawler Join Date: Aug 2007 Location: mesa az
Posts: 657
| |
01-15-2009, 06:03 PM | #14 |
Rock Crawler Join Date: Dec 2007 Location: GILBERT
Posts: 751
| |
01-16-2009, 07:30 AM | #15 |
Quarry Creeper Join Date: Jun 2008 Location: Mesa
Posts: 199
|
I am in! See ya out there
|
01-16-2009, 11:11 AM | #16 |
Newbie Join Date: Jul 2008 Location: chandler AZ
Posts: 32
|
wish i could...gotta work though...damn work!
|
01-16-2009, 02:43 PM | #17 |
Newbie Join Date: Dec 2008 Location: Gilbert
Posts: 33
|
Any one in the gilbert area wanna car pool? Count me in! Got some steering issues addressed, I'm ready to go!
|
01-16-2009, 03:43 PM | #18 |
Rock Crawler Join Date: Dec 2007 Location: GILBERT
Posts: 751
|
i'll pick you up. gimme a call.
|
01-16-2009, 06:29 PM | #19 |
Newbie Join Date: Jan 2009 Location: Mesa
Posts: 0
|
see ya there
|
| |