Re: Xtra Speed axle
 

That looks sweet.For that value,its a bomber,especialy if it fits nice

Re: Xtra Speed axle
 

Glad to hear some feedback on these, I've got some on order but I wasn't sure what to expect..

Re: Xtra Speed axle
 

I originally only ordered one for the front to check it out. I was so impressed, the rear shows up tomorrow!

Sent from my SM-N910P using Tapatalk

Re: Xtra Speed axle
 

I have also ordered a pair after rounding off the splines on one side of my stock front plastic axle. I'll be using them with SSD c-hubs up front and will update when I get them installed and tested.

--Hector

Re: Xtra Speed axle
 

I also rounded the splines on one side of my stock housing on my first big run... is that usual? anyone else have this problem with aluminum chubs and stock axles? I pulled the trigger on a set of these last week so now its the waiting game. If these work out nice I might build a set for my old scx10 jeep.

Re: Xtra Speed axle
 

I just posted this same question on a facebook page. I stripped my splines on the stock housing in less than two hours on my first run. I am also using ssd chubs. I ordered these housings about a week and a half ago. Seems like a great value. We will see

Re: Xtra Speed axle
 

Got my xtra speed axle housings today! I am so impressed for less than $50 shipped for both! They are beautiful and was a breeze to install. Only problem I had was getting the internal (larger) drive shaft bearing in. Seemed that the paint made it just too tight of a squeeze. After some careful dremeling they were perfect. Just the housing itself weighed more than the entire stock front axle with the Ssd chubs, knucks, and axial axle shafts. More than 100grams more than stock. Gonna take a wire wheel to the diff covers as soon as I can and get that red off of there! Anyone looking for new housings, I suggest these!

https://scontent.fsnc1-1.fna.fbcdn.n...e7&oe=58D693CA

https://scontent.fsnc1-1.fna.fbcdn.n...1e&oe=58771F68

https://scontent.fsnc1-1.fna.fbcdn.n...6b&oe=58764ABF

Re: Xtra Speed axle
 

will be interesting to see how these hold up after some time goes being run on the rocks and taking tumbles as well...

Re: Xtra Speed axle
 

I think I like the diff covers silver. A wire wheel made short work of the red.
http://i1243.photobucket.com/albums/...psvugi32wy.jpg

Sent from my SM-N910P using Tapatalk

Re: Xtra Speed axle
 

For sure. The red would have gotten all scuffed up any way.

Re: Xtra Speed axle
 

Nice work Shawn, that looks GREAT. So much better then the red FTW, "thumbsup"

~D

Re: Xtra Speed axle
 

http://i1243.photobucket.com/albums/...pskuykepqv.jpg
Was thinking about trying to polish, naaaah!

Sent from my SM-N910P using Tapatalk

Re: Xtra Speed axle
 

Based off of the reviews here, I went and ordered a set of the axle housings. My buddy also got some for his V1 SCX10, which add double the weight these do apparently.

Has anyone found these incompatible with certain other parts?

Re: Xtra Speed axle
 

Imagine these axles mated with those new brass knuckles from Hot Race. So much weight down low.

Re: Xtra Speed axle
 

diff cover looks great silver how are the holding up around the pinion bearing any play? and wear on the rocks. does the stock diff cover fit the xtra speed axle case bye any chance

Re: Xtra Speed axle
 

I don't think it's been discussed exactly what metals are used to make the alloy in these Xtraspeed housings, but you may want to spray some clear coating over the silver diff cover to prevent rusting. I think they look more scale with the silver instead of red, but I like having the protective coating for at least my first couple of runs lol.

Re: Xtra Speed axle
 

It is aluminum, no rust. The bearings all around are a great fit. I am using steel pivot balls in the links, needed to sand the paint down to fit in the link mounts. Don't have a ton of time on them but so far so good.

Sent from my SM-N910P using Tapatalk

Re: Xtra Speed axle
 

The axle is a clone of the stock. The Axial covers do fit and I would imagine any aftermarket would as well.

Sent from my SM-N910P using Tapatalk

Re: Xtra Speed axle
 

Ah, I was under the impression they were alloy, not 100% aluminum. Thanks for clarification.

Re: Xtra Speed axle
 

thats good to hear thanks guys for the info