02-04-2017, 09:45 AM | #1 |
Rock Crawler Join Date: Mar 2013 Location: Waukesha
Posts: 635
| Swb link set?
Did a quick search with nothing I was looking for. Does anyone make a swb link set yet for these trucks. I'm looking at dropping down one of my trucks to the 11.4 for a blazer body I want to build. If not I could build my own I suppose. Sent from my iPhone using Tapatalk |
Sponsored Links | |
02-04-2017, 10:00 AM | #2 |
Quarry Creeper Join Date: Dec 2010 Location: Hanford
Posts: 318
| Re: Swb link set?
I looked too and think you can use an extra set of front links for the rear to get pretty close. I thought about it for the same reason and with the rc4wd blazer body sitting on top of the kit it's way off. Although the front is 3 linked you can buy the links in pairs.
|
02-04-2017, 10:03 AM | #3 |
Rock Crawler Join Date: Mar 2013 Location: Waukesha
Posts: 635
| Re: Swb link set?
I thought the rc4wd blazer was setup for the 12.3 wheelbase of the tf2 Sent from my iPhone using Tapatalk |
02-04-2017, 10:34 AM | #4 |
Quarry Creeper Join Date: Dec 2010 Location: Hanford
Posts: 318
| Re: Swb link set?
11.3 for the rc4wd blazer. I have a vaterra blazer coming that is 12.3. I used 12.3 WB vanquish links reconfigured on my rc4wd blazer mud truck with ar60's to achieve the right WB.
|
02-04-2017, 10:53 AM | #5 |
Quarry Creeper Join Date: Dec 2010 Location: Hanford
Posts: 318
| Re: Swb link set? |
02-04-2017, 11:02 AM | #6 |
Rock Crawler Join Date: Mar 2013 Location: Waukesha
Posts: 635
| Re: Swb link set?
I've got the regular tf2 Mohave2. The proline blazer is the one I had on my last scx. 11.3 wheelbase fit good. Sent from my iPhone using Tapatalk |
02-04-2017, 11:36 AM | #7 |
Quarry Creeper Join Date: Dec 2010 Location: Hanford
Posts: 318
| Re: Swb link set?
Your tf2 should have the same 11.3 WB as the blazer that was made for it. I also had a proline blazer on an old scx10, but had to make links for that one. It was a little smaller at 11.2" WB. Is the proline the one you're planning on using? Have you looked into a vaterra blazer body? You can keep the longer WB and it has a 3d grill. Here was my old proline blazer, I didn't like the WB so short on that one, I never got it dialed in. [IMG][/IMG] |
02-04-2017, 11:41 AM | #8 |
Rock Crawler Join Date: Mar 2013 Location: Waukesha
Posts: 635
| Swb link set?
I loved the shorter wheel base on the old truck. Since I have two of the kits. I'm going to keep one long and one short. Right now I'm using the included jeep body on the one I just built. Which I'll keep 12.3 Sent from my iPhone using Tapatalk |
02-04-2017, 11:50 AM | #9 |
Quarry Creeper Join Date: Dec 2010 Location: Hanford
Posts: 318
| Re: Swb link set?
Well good luck with it. The new axles should make pinion angles much better on a swb. Check into putting front (4) links on the rear and see where that gets you. Start a thread when you get it going.
|
02-04-2017, 12:11 PM | #10 |
Rock Crawler Join Date: Mar 2013 Location: Waukesha
Posts: 635
| Re: Swb link set?
Definitely Sent from my iPhone using Tapatalk |
Swb link set? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TF2 SWB, MST CMX, or STRC SCX10 SWB? | aver3 | General Crawlers | 2 | 11-22-2016 07:26 PM |
Rc4wd TF2 SWB 3 link front | whitrzac | RC4WD Trail Finder 2 | 3 | 04-08-2016 02:09 AM |
MIP Dig set work in a SWB SCX? | meatmonkey | Newbie General | 4 | 06-12-2012 09:04 PM |
| |