| |
06-03-2013, 10:01 AM
| #1 |
| Rock Stacker Join Date: Feb 2012 Location: Pittsburgh
Posts: 71
|  Drive shaft set screws
Anyone know where to get some extra set screws? I have two wraith kits, one finished, one under construction. First run, lost a set screw. I know, loctite, my dumb ass mistake. Well I am going to order MIP today. I just want to have some extra set screws for backup.
|
|  |
| Sponsored Links | |
| | |
|
06-03-2013, 11:14 AM
| #2 |
| Rock Stacker Join Date: Feb 2012 Location: Pittsburgh
Posts: 71
| Re: Drive shaft set screws
Never mind, I figured it out. I looked at the axial part number from my instructions and found them at ckrc.
|
|
| |
|
06-03-2013, 11:36 AM
| #3 |
| Rock Crawler Join Date: Feb 2012 Location: Michigan
Posts: 617
| Re: Drive shaft set screws
The MIP's use a 4mm set screw, not 3mm that Axial uses.
|
|
| |
|
06-03-2013, 12:47 PM
| #4 |
| Rock Stacker Join Date: Feb 2012 Location: Pittsburgh
Posts: 71
| Re: Drive shaft set screws
On RPP site, the description says it uses the 3mm axial screws...
|
|
| |
|
06-03-2013, 10:43 PM
| #5 |
| I wanna be Dave Join Date: Jan 2012 Location: CANADA
Posts: 2,648
| Re: Drive shaft set screws
After I loctite mine in I also wrap electrical tape around the collar...that helps if they loosen off even with blue loctite. Just a little extra insurance. Maybe I am crazy but I think I read this tip somewhere before.
|
|
| |
|
06-04-2013, 03:39 AM
| #6 | |
| Pebble Pounder Join Date: Nov 2012 Location: Stoke on trent , England
Posts: 159
| Re: Drive shaft set screws Quote:
The rest use the 4mm revo style ones . Jack. | |
|
| |
|
06-04-2013, 06:29 PM
| #7 |
| Quarry Creeper  Join Date: Feb 2011 Location: Princeton Illinois
Posts: 477
| Re: Drive shaft set screws
either one of these will work TowerHobbies.com | Traxxas Screw Pins 4x13mm w/Threadlock (4) TowerHobbies.com | Traxxas Screw Pin 4x15mm Revo (6) |
|
| |
|
06-04-2013, 09:23 PM
| #8 |
| Rock Stacker Join Date: Feb 2012 Location: Pittsburgh
Posts: 71
| Re: Drive shaft set screws
I found some Traxxis ones at a lhs. Now I know about MIPS too. Thanks for all the imput, you guys are great with helping an idiot like me.  |
|
| |
|
06-05-2013, 08:47 PM
| #9 |
| I wanna be Dave Join Date: Dec 2012 Location: idaho
Posts: 2,658
| Re: Drive shaft set screws
I tried blue lokt tight with no luck. Just had to check them every ounce in awhile. I've switched to tmaxx and revo drive lines and they never back out. |
|
| |
|
06-06-2013, 08:35 AM
| #10 | |
| I wanna be Dave Join Date: Sep 2005 Location: Houston, TX
Posts: 16,952
| Re: Drive shaft set screws Quote:
| |
|
| |
 |
Drive shaft set screws - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Part number to 4mm hex drive set screws on Mcmaster | 4xFord | Tools, and Procedures | 3 | 02-14-2010 07:38 PM |
| Axial Drive Shaft Set | sally1800 | Axial SCX-10 | 4 | 06-07-2009 10:09 PM |
| |
Linear Mode
