06-27-2012, 02:56 PM | #1 |
Pebble Pounder Join Date: Sep 2008 Location: n.e.pa
Posts: 156
| 3pk and a wench control
so i hooked up my wench control to the 3pk and it works as it should using the 3pos. 3rd channel. however it seems to chatter an awful lot when in the neutral pos. so would anyone have any input as to the reason for this. i checked the sub trims and all that i could think of but its still there. i dont want to burn up the little motor inside as it seems to be getting warm. i have this set exactly the same way on the other channel for my punk dig and it doesent glitch or anything. i know its right but i dont know exactly what the chattering is from seems to be getting extra voltage from some place like a bleed i guess you could say. 3pk with a spektrum module rc4wd wench control Last edited by activethunderrc; 06-27-2012 at 03:10 PM. |
Sponsored Links | |
06-27-2012, 03:31 PM | #2 |
Newbie Join Date: May 2012 Location: Chico
Posts: 35
| Re: 3pk and a wench control
Wench control? Slap that wench in the mouth, backhand. If she still doesn't listen, slap her again. |
06-27-2012, 03:34 PM | #3 |
Pebble Pounder Join Date: Sep 2008 Location: n.e.pa
Posts: 156
| Re: 3pk and a wench control
never mine i seized the motor trying to figure it out
|
06-28-2012, 05:25 AM | #4 | |
I wanna be Dave Join Date: Nov 2010 Location: 07456 N. NJ USofA
Posts: 8,314
| Re: 3pk and a wench control Quote:
Active, it's likely due to the winch controller. HeyOK makes a replacement controller that fixes the "servo jitters". | |
06-28-2012, 08:14 AM | #5 |
Pebble Pounder Join Date: Mar 2011 Location: Aurora, CO
Posts: 197
| Re: 3pk and a wench control
You may also need to run the general setting instead of the High speed or HRS setting for receiver signal type depending on the type of controller used. Marcus |
07-20-2012, 11:28 PM | #6 | |
Newbie Join Date: May 2012 Location: Southfield
Posts: 1
| Re: 3pk and a wench control Quote:
| |
07-20-2012, 11:34 PM | #7 |
Rock Crawler Join Date: Dec 2011 Location: Las Vegas 89110
Posts: 585
| Re: 3pk and a wench control |
07-21-2012, 12:28 AM | #8 |
Rock Stacker Join Date: Jan 2011 Location: Australia
Posts: 54
| Re: 3pk and a wench control
Hmmm, might head into Surfers and do me some wenching this very even, methinks! |
07-21-2012, 05:11 AM | #9 |
RCC Addict Join Date: Jan 2012 Location: Sweden
Posts: 1,809
| Re: 3pk and a wench control |
3pk and a wench control - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
mount a wench? | RaMvsRC | Newbie General | 7 | 11-25-2010 08:49 PM |
futaba 3pk..can it be used to control two esc? | gkslacker | Newbie General | 4 | 09-30-2010 11:11 AM |
servo wench | pat | Newbie General | 3 | 10-04-2007 12:54 PM |
wench | rcrobert | Comments, Suggestions, and Help | 5 | 04-28-2007 02:23 AM |
wench idea I trying in my new crawler.... | Jeeprockcrawler | General Crawlers | 4 | 10-06-2005 09:34 PM |
| |