|
| LinkBack | Thread Tools | Display Modes |
11-01-2017, 12:31 PM | #1 |
Newbie Join Date: Dec 2006 Location: brockway
Posts: 38
| flysky hack 2 position winch controller
Guys, I have searched with out any success. I recently had my 3b hacked. I am trying to figure out how to program the 3rd channel for a 2 position winch control. Any help would be great. thanks |
Sponsored Links | |
11-01-2017, 04:24 PM | #2 |
Rock Crawler Join Date: Aug 2007 Location: Philadelphia
Posts: 797
| Re: flysky hack 2 position winch controller |
11-03-2017, 08:55 PM | #3 |
RCC Addict Join Date: Aug 2017 Location: Fredericksburg, VA
Posts: 1,912
| Re: flysky hack 2 position winch controller
Problem is that is a 3 position winch channel he programs in that video set up for -100/0/+100. The OP has a 2 position controller, IE, click cable out click cable in. Now that said, it might be possible to program that channel to send +100/0/+100 each direction of the switch throw. The problem with that is that the winch will change direction each time the switch is thrown in any direction which could get very confusing. Or maybe program the channel to 0/0/+100 that way the switch would only activate the 2 position controller in one direction of the switch throw. I'm just speculating here, I haven't tried anything like that with my GT3C because I have a 3 position winch controller.
Last edited by Inspector86; 11-03-2017 at 10:18 PM. |
11-04-2017, 06:14 PM | #4 |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Re: flysky hack 2 position winch controller
Scroll to REV, press and hold enter Scroll to C, press enter Scroll to CH3, press enter Scroll to MO1, press and hold enter Press back/end afew times That will assign your channel 3 button (on the handle) to control channel 3 in a momentary 2 postion manner So it will always be at -100. when you press and hold it will be at +100. when you let off it goes back to -100 Assuming your winch controller uses the position upon power up for "off", then this should work. If it works another way, you may need to choose MO0 (instead of MO1) for non-momentary control. But then you need to remember to press the button to deactivate the winch. |
11-06-2017, 05:34 AM | #5 |
Newbie Join Date: Dec 2006 Location: brockway
Posts: 38
| Re: flysky hack 2 position winch controller
I tried the program in MO1 & MOO still did not work. The two position switch is a hey ok winch controller if that help solves the issue. thanks |
11-06-2017, 06:32 AM | #6 |
I wanna be Dave Join Date: May 2007 Location: Vancouver, BC
Posts: 2,379
| Re: flysky hack 2 position winch controller
It's hard to know if the controller is faulty or the transmitter is programmed to do what you want. My suggestion is to connect a servo to your winch channel as it will help you visualize what is happening. Pushing the button on the handle should make the servo move from one end to the other. If the servo is doing what you expect, then maybe the winch controller has a problem. |
11-06-2017, 07:06 AM | #7 |
Newbie Join Date: Dec 2006 Location: brockway
Posts: 38
| Re: flysky hack 2 position winch controller
I do not believe the controller is bad. It works fine on another remote, just not on the hacked remote. I believe its a programming in the controller.
|
11-07-2017, 10:56 AM | #8 |
Rock Crawler Join Date: May 2016 Location: SoWIs
Posts: 618
| Re: flysky hack 2 position winch controller
A 2 position channel is simply +100 or -100. If you have a 3 position switch/channel you simply have to deal with an extra click in the middle [that does nothing]. A 2-pos channel simply waits for a 200% change (a 1000us change to be precise). If you switch it to the receiver's CH1 you can test it with the steering wheel, assuming it's set to 100% endpoints & no dual rates. Full lock one way then full lock the other should activate it. Likewise you can plug a servo into the receiver's CH3 and test your 3B's programming. One last thing, I thought the 3B would be like my 3C in which CH3 was a 2-pos by default. My 3C sets CH3 to zero (1500us) when turned on, the each press moves it alternating full lock (2000us or 1000us). |
11-11-2017, 03:59 PM | #9 | |
Got Worms? Join Date: Jun 2009 Location: Golden, CO
Posts: 6,116
| Re: flysky hack 2 position winch controller Quote:
Plug a servo into the ch3 rx slot to see what is happening. The template I gave you should work. | |
11-11-2017, 04:05 PM | #10 |
Newbie Join Date: Dec 2006 Location: brockway
Posts: 38
| Re: flysky hack 2 position winch controller
Got it to work. Thanks for all the help Sent from my iPhone using Tapatalk |
flysky hack 2 position winch controller - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Winch Controller for Radio with 2 Position Third Channel | heyok | Vendors Electronics | 121 | 05-19-2020 03:08 PM |
Flysky GT3B Hack PSX's Custom Firmware 0.61 How to hack? 8 channel 4-wheel steering D | boolean21 | Scale Videos! | 0 | 06-22-2013 12:15 AM |
Need advice on radio/hack/winch controller,im kinda lost here | ProfitOfDoom | Electronics | 7 | 04-14-2013 06:36 PM |
| |