Re: Silent outrunner and ESC for less then $60
 

The swd and swc are only needed to upload the bootloader. After that you just unsolder them.

Sent from my SM-N986U using Tapatalk

Re: Silent outrunner and ESC for less then $60
 

I don't know, there is a compatibility list on the githubs wiki. If it's not listed just try a few different ones.

Sent from my SM-N986U using Tapatalk

Re: Silent outrunner and ESC for less then $60
 

well, it started, flashed esc dys aria 70a using st-link, used options wrait, iflight, tmotor55. esc does not respond in the ESCConfigurator program, what should I do in this case? please write as stupid)))

update, it worked, at first wrait_full (it didn't work well, it was still fine at low speed, but when the stroke increased, the motor stopped spinning and made terrible noises), then updated via arduino HGLRC 60A, it became much better, straight good, but at low speed there is intense heating of the motor and regulator, at low speed the uneven operation of the motor was noticed, I would like it smoother, how can I do this?

Re: Silent outrunner and ESC for less then $60
 

What are your settings in the configurator ? Can you do a screen shot?

Re: Silent outrunner and ESC for less then $60
 

Hey man, are there any recommended settings? I just copied those from the instructions on Github

Re: Silent outrunner and ESC for less then $60
 

A bit of video comparing the difference between using a Castle Sidewinder 4 and an IFlight 55a. Would have liked to do more but my GoPro was flat which I swear I checked the night before! Did an intro at the start but not sure if that adds much to it, would be interested to hear any *constructive* feedback on your thoughts on that "thumbsup"https://youtu.be/SftLIlK2pkU

Re: Silent outrunner and ESC for less then $60
 

I changed the pwm frequency (set 48) and lowered the timings(7, 5)

Re: Silent outrunner and ESC for less then $60
 

Sidewinder have sound because he have low frecency pwm, lower like 24kHz

Re: Silent outrunner and ESC for less then $60
 

I asked the local esc production masters to familiarize themselves with the am32 firmware, maybe they can tell us something, experience in this area since 2009, they just specialize in the production of regulators on stm32 processors

Re: Silent outrunner and ESC for less then $60
 

So I may be able to get the IFlight to run even quieter by changing the PWM frequency?

Re: Silent outrunner and ESC for less then $60
 

yes, and unfortunately we will increase heating and energy consumption at low speeds, so they explained to me the principle of operation of power transistors... perhaps they will find a way around this nuisance.

Re: Silent outrunner and ESC for less then $60
 

https://youtu.be/evvfd1Z7om0
https://youtu.be/rMB2_Ovx7Ag

Re: Silent outrunner and ESC for less then $60
 

????:shock: I dont get it ..... could you post a screenshot of your settings?

Re: Silent outrunner and ESC for less then $60
 

I use the stock settings of the wraith 32 firmware, when changing the pwm frequency to 48kHz, I observe problems with switching modes, is it possible to somehow reduce the heating level at low speed by changing the firmware?

Re: Silent outrunner and ESC for less then $60
 

i try HGLRC T-rex 60A with PA2 bootloader and wraith firmware not work...anyone have try the HGLRC ????

Re: Silent outrunner and ESC for less then $60
 

I use HGLRC on dys aria 70a, it work is well

Re: Silent outrunner and ESC for less then $60
 

1.74 hglrc?? and how about the partial bin??

Re: Silent outrunner and ESC for less then $60
 

Yes, 1,74 HGLRC, what your esc? Show how it works

Re: Silent outrunner and ESC for less then $60
 

I first installed the full firmware wraith_crawler_1450kv_full, then updated it via arduino HGLRC, try this, I didn't use a separate bootloader

Re: Silent outrunner and ESC for less then $60
 

my esc is hglrc 60a but not work..try 1.74 wraith 1460kv work on slow throtle...and hard cogging and not spinning on midle and high input...