01-04-2021, 02:56 AM | #1 |
Newbie Join Date: Jul 2020 Location: aus
Posts: 1
| Sanwa m12 moa dig
Gday I recently picked up a sanwa m12 and finally can run proper dig and burn on my Xr10. I've been messing about with it and I've got it working kinda. How do I setup variable overdrive and dig at the same time? If I set the lever (or a trim switch) to the moa mixing I can do dig and burn with the selected control but I can't figure out how to make the variable overdrive work the manual mentions it can be done but not how. Any pointers? Sent from my Pixel 4 XL using Tapatalk |
Sponsored Links | |
01-29-2021, 07:02 AM | #2 |
Newbie Join Date: Jul 2019 Location: France
Posts: 3
| Re: Sanwa m12 moa dig
Hello, you have found a solution for this problem, I am in the same situation, I just received this remote and I am blocked ...
|
01-29-2021, 09:15 AM | #3 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Sanwa m12 moa dig
Depends on the m12 from what I understand. The m12rs doesn't have the same dig setup as the earlier m12 or m12s. I have an mt4 and the mixing is on the lever and variable drive bias is on the dial. I don't use the dial though, my thumb never leaves the lever, I'm always adjusting the mix, it's not something you just set and leave on a MOA.
|
02-03-2021, 01:01 PM | #4 |
Newbie Join Date: Jul 2019 Location: France
Posts: 3
| Re: Sanwa m12 moa dig
thank you for the answer, i have the m12 RS and so for you i can't do the dig mixing like the mt4....? (i don't really understand what i cannot do and some word (explanation in english are difficult for me sorry...) So for an moa it's not good...? After reading again the manual i understand....i can't assign the dig on lever only the MOA Mix !!!! So White Trash you were right........ Great,this radio it's not good for MOA............. Last edited by Ftek23; 02-03-2021 at 04:04 PM. |
02-04-2021, 12:01 AM | #5 | |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Sanwa m12 moa dig Quote:
Sometimes translation loses information but I think we can work though it well enough. On an earlier model airtronics with a lever you can use the lever to change the mix front and rear and the dial does the same thing but it is easier to leave it at +20 front etc so when the lever is at 0 mix the front still has overdrive. | |
02-09-2021, 02:26 PM | #6 |
Newbie Join Date: Jul 2019 Location: France
Posts: 3
| Re: Sanwa m12 moa dig Ok i understand thank you I solve the problem....i keep the m12 for my other rig and i bought an mt4 for the MOA |
02-09-2021, 02:58 PM | #7 |
I wanna be Dave Join Date: Aug 2004 Location: Tri-cities, WA
Posts: 4,831
| Re: Sanwa m12 moa dig
That's the easy solution, I'm very happy with my mt4.
|
09-30-2021, 11:51 AM | #8 |
I wanna be Dave Join Date: Feb 2009 Location: Detroit
Posts: 2,075
| Sanwa m12 moa dig
System-assign-lever- moa mix scrolling all the way up. It works on the m12s rs. Only problem is, mine doesn’t stay assigned. So every time I switch models or turn off radio, it losses the assigned function. If yours doesn’t work at all, you need the updated firmware. Sent from my iPhone using Tapatalk |
Sanwa m12 moa dig - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Sanwa MT4 a can I use it for 4WS and dual esc dig | Alonjp | Electronics | 0 | 09-12-2015 01:03 PM |
Airtronics M12 !!!!! | nissan_driver24 | Electronics | 15 | 05-24-2013 01:32 AM |
| |