|
| LinkBack | Thread Tools | Display Modes |
10-28-2023, 10:27 PM | #1 |
Quarry Creeper Join Date: Feb 2020 Location: Bakersfield
Posts: 237
| Axle shaft and drive shaft
I just finished my GK build and snapped my universal within minutes of first rolling. Wheels were not locked up, End points were set and no apparent binding. My Google foo is failing me right now. Drive shafts I’ve got covered but really looking for front axle shafts. I’ve read the the 10.2 from axial work. What are out current offerings or substitutions? |
Sponsored Links | |
10-29-2023, 07:00 AM | #2 |
I wanna be Dave Join Date: Jan 2016 Location: california under the rock im crawling on
Posts: 4,289
| Re: Axle shaft and drive shaft
Google fooie found this in seconds https://www.ebay.com/itm/13461075728...mis&media=COPY the listing dose say scx10ii or Enduro so they might be the same there are also lots of element labeled units for the $40+ range maybe there stronger I don't know but they sure cost more |
10-30-2023, 10:18 AM | #3 |
Quarry Creeper Join Date: Feb 2020 Location: Bakersfield
Posts: 237
| Re: Axle shaft and drive shaft
Yea because I trust eBay. I’ve only read from a few places that they should work. I’ll be looking into some cvd’s maybe.
Last edited by hnoroian; 10-30-2023 at 10:29 AM. |
11-03-2023, 10:23 PM | #4 |
Quarry Creeper Join Date: Feb 2020 Location: Bakersfield
Posts: 237
| Re: Axle shaft and drive shaft
Well I ordered some SSD 10.2, hope they fit.
|
11-04-2023, 07:02 AM | #5 |
I wanna be Dave Join Date: Sep 2011 Location: Douglassville, PA
Posts: 4,227
| Re: Axle shaft and drive shaft
That's an odd part to break -did you reach out to Element? Might have been a bad part.
|
11-04-2023, 09:41 PM | #6 | |
Quarry Creeper Join Date: Feb 2020 Location: Bakersfield
Posts: 237
| Re: Axle shaft and drive shaft Quote:
Last edited by hnoroian; 11-04-2023 at 09:43 PM. | |
11-07-2023, 02:05 PM | #7 |
Quarry Creeper Join Date: Feb 2020 Location: Bakersfield
Posts: 237
| Re: Axle shaft and drive shaft
So the 10.2 axles do work but when I snugged down the lock nut in the wheels with the new axles I ended up binding the hexes to the hubs. I swapped out some screw pins for wheel hexes and that seemed to alleviate the binding. Now that makes me wonder if that’s what happened the first time but it seemed to roll pretty easily before. Now I need to take it for a test run.
|
Axle shaft and drive shaft - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Scx24 JLU Drive shaft, Axle Question | Steelone232 | Micro Scale Rigs | 3 | 06-04-2023 02:37 PM |
best way to join a rwvo drive shaft to the output shaft on the axle | TRAV | Kyosho Crawlers | 12 | 01-29-2012 07:37 PM |
Tlt Axle/drive Shaft Problems | rc_phanatic | Tamiya TLT Crawlers | 10 | 03-28-2007 05:58 PM |
Stainless Steel Drive & Axle Shaft are here | rc4wd | General Crawlers | 0 | 08-30-2005 10:33 AM |
| |