RCCrawler Forums

RCCrawler Forums (http://www.rccrawler.com/forum/)

- EnRoute Berg (http://www.rccrawler.com/forum/enroute-berg/)

- - Asso V3 (http://www.rccrawler.com/forum/enroute-berg/424066-asso-v3.html)

Wow! I'm not sure what to say. When I see someone take renderings and make them reality, its just exciting to watch!!! I can't wait to see more pics!!

dude that chassis i trick as hell, im assuming you kinda toke some ideas from the nano tracer?
Good Job!

What's your plan with the axles? They are v3 axles? Can you post up how you're going to modify them?

Thanks, fellow V3 guy.

Those look great! What axle shafts are you using? Does a V1 locker fit in the housing?

They look awesome, I have a set of berg V2 and have been looking at doing the same thing but i have no tools to do it. It has to be saving a heap of weight.
Keep the pics coming please.....

I have got a wraith mod going on too... Driveshafts, knucles and c-hubs are coming to me... I did mod the Axial Ax-10 locker to fittin to the axle and welded it to the main gear... "thumbsup" Hopefully i´ll get all parts soon... :mrgreen:

Here are some photos

Change to cvd with hose 6/4 mm steel
I internally threaded tube M5 and cvd axial always M5, then a plug will be to ensure that not unscrew

https://lh4.googleusercontent.com/-9...129_200451.jpg

https://lh5.googleusercontent.com/-g...129_200242.jpg

https://lh4.googleusercontent.com/-3...129_200314.jpg

https://lh3.googleusercontent.com/-M...129_200401.jpg

so how is it going? how much does the chassis alone weigh?

Wow, that looks great! Can you shoot over more information?? Specific Dimensions ETC?

Thanks! "thumbsup"

:)
This below is the change
Rebuilt drive shafts with steel tubes for two reasons
Weight and because information Employment easier, especially from fillettare
The axial cvd forced me on this choice to find a way to unite them
Cvd M5, M5 pipe tapped always everything together and secured with loctite final

https://lh4.googleusercontent.com/-2...201_215028.jpg

Here we see the assembled short, the ingranagi I put them on the other hand because of the thorns of the crown axis

https://lh6.googleusercontent.com/--...9821627517.jpg

Here the case is closed, the drive shaft protruding screw is screwed where the spool

https://lh5.googleusercontent.com/-W...9819183003.jpg

Spool screwed and secured with two grains, those berg tip 2mm sinking into the axle

https://lh3.googleusercontent.com/-J...9819258690.jpg

Mounted along the axle shaft that engages the spool and always stuck with the two grains

https://lh3.googleusercontent.com/-6...9820465967.jpg

To make the long tube inner diameter of 12 mm may be to place all the components I have lowered
The spool is 10mm while the cvd originally were 12.2mm I took them to 11.9 mm
The tube instead is fixed to the case from the outside

https://lh6.googleusercontent.com/-e...202_173401.jpg

very nice
but it won't work with V2 axles as i have taken a notch out to fit the servo between the motor and the axle.
keep up the great work.

the servo does not fit between the axle and motor :cry:

https://lh3.googleusercontent.com/-i...126_020613.jpg

Quote:

Originally Posted by spyder_4193 (Post 4160955)

very nice

This a link to my build
http://www.rccrawler.com/forum/enrou...s-berg-v2.html

"thumbsup"