05-13-2013, 12:54 PM | #1 |
Newbie Join Date: May 2013 Location: NW
Posts: 19
| V3 tracer
I bought a v3 tracer roller and i have been searching for info on the best setup for it, but havent found much info, does anyone have any suggestions on a power package for it. Ive read that the axles are set up for the brushless 540 type motor and its all a bit confusing. If anyone has some input it would be greatly appriciated
|
Sponsored Links | |
05-13-2013, 01:46 PM | #2 |
RCC Addict Join Date: Jan 2010 Location: Dallas
Posts: 1,848
| Re: V3 tracer
I am not sure many guys on this forum run the V3. Mostly just V1 but patient as a few may pop up.
|
05-13-2013, 01:46 PM | #3 |
Fifth dimension Join Date: Oct 2012 Location: Quakertown
Posts: 2,066
| Re: V3 tracer
Your not going to get much help because there is any brother. When berg came out with the v1's, that was their peak. I'm not saying you won't have tons of fun with your v3. I'm just saying design wise, I've never seen anyone use these axles. If its just a conversation about electronics, we would need to know what radio and what type of dig you plan to use. I use 2 micro mamba pro's, cc bec, hitec 7950 servo and holmes hobbies 35 turn motors. I think you'll find most run something similar. If you want, you can run a m2 dig or punk dig with one esc. It's good to start. Just tryin to help |
05-13-2013, 05:28 PM | #4 |
Newbie Join Date: May 2013 Location: NW
Posts: 19
| Re: V3 tracer
Thanks. I did some reading and the v3 isnt that great of a platform to start with. Oh well back to sqare one
|
05-13-2013, 05:34 PM | #5 |
Fifth dimension Join Date: Oct 2012 Location: Quakertown
Posts: 2,066
| Re: V3 tracer
For real bud, don't feel like your the only one. I was half way through my first build before I found this forum. I waisted a lot of money! Into my first competitive season now |
05-13-2013, 06:30 PM | #6 |
Newbie Join Date: May 2013 Location: NW
Posts: 19
| Re: V3 tracer
Anyone have any advice on where to start so i dont have to do this again. Whats the bullet proof setup for a moa crawler
|
05-14-2013, 06:58 AM | #7 |
Fifth dimension Join Date: Oct 2012 Location: Quakertown
Posts: 2,066
| Re: V3 tracer
Dlux berg axles. I love mine!
|
05-14-2013, 07:57 AM | #8 |
I wanna be Dave Join Date: Aug 2008 Location: Deep in Swing Town
Posts: 3,011
| Re: V3 tracer |
05-15-2013, 12:31 AM | #9 |
DravTech Join Date: Aug 2012 Location: Sweden
Posts: 643
| Re: V3 tracer
I would say keep the V3 rear axle, then buy a V1/dlux/MT one for the front.
|
V3 tracer - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Tracer | crawl-o-matic | EnRoute Berg | 2 | 04-26-2011 03:19 PM |
My ..CLASSIC TRACER.. | loverichey | EnRoute Berg | 10 | 07-28-2010 11:59 AM |
r2 in a tracer | intimadationrc | General Crawlers | 7 | 08-15-2007 06:47 PM |
TLT/Tracer | DWillz | Tamiya TLT Crawlers | 5 | 02-09-2007 08:17 PM |
| |