11-14-2008, 03:38 AM | #1 |
Rock Crawler Join Date: Jun 2006 Location: Sinking Spring
Posts: 572
| Diff issues
I have some major diff problems and need to know the best way to get in touch with Kyosho to order new ones. I just need their e-mail address or phone number. Or if somone has some Twin Force diffs complete that they would be willing to get rid of just pm me. Thanks in advance! ThanX, Krystopher |
Sponsored Links | |
11-14-2008, 02:47 PM | #2 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
|
Watcha need? I have a lot of stock diffs since I only run CDW spools.
|
11-15-2008, 08:47 AM | #3 |
Rock Crawler Join Date: Jun 2006 Location: Sinking Spring
Posts: 572
|
I need the diff housing with spider gears, drive cups, and the bearings.
|
11-15-2008, 11:34 AM | #4 |
Newbie Join Date: Jun 2008 Location: Barstow
Posts: 37
|
Need diff for kyosho mad/twin force. I think it's the hellfire that fits. That's what I got in mine. I would be interested in what you are doing with the hex/stub issue. I'll be keeping an eye on you as well as finding out about turning those savages down.
|
11-15-2008, 11:56 AM | #5 |
Rock Crawler Join Date: Jun 2006 Location: Sinking Spring
Posts: 572
|
Would you know where I can get the Hellfire diff? Is it completely compatable with a Twin? Such as bearings, drive cups, and the housing? ThanX, Krystopher |
11-16-2008, 08:33 AM | #6 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
|
Most 1/8th scale buggy diffs fit. Tower is a HPI dealer, Hot Boddies, and Ofna also work. I have some that work listed in the Mods Sticky. You could upgrade to 4 spider set up for more strength. Most of the buggy diffs are steel gears instead of pot metal like the Twin's. I don't have any complete diffs but I do have spiders, sides, and housings. I use the drives. If your interested let me no. PM
Last edited by Bart bender; 11-16-2008 at 08:36 AM. |
08-08-2009, 10:58 PM | #7 |
Rock Stacker Join Date: Mar 2008 Location: schirever
Posts: 61
|
I just installed a Ofna Hyper 7 diff and pinion in a MadForce axle |
08-29-2009, 05:01 AM | #8 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| I have a hyper 7 diff in my axle and it seams to slide from side to side like the Hyper diff is to narrow ?? What is the width of the Kyosho and Hellfire diff at the outside of the bearing |
08-29-2009, 08:18 AM | #9 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
|
You'll need to shim it to keep the ring gear in proper contact with the pinion.
|
08-29-2009, 03:30 PM | #10 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| I know that but it seems like 2.5-3mm ?? If I push it all the way over to one side the pinion don't have any contact with the ring gear I think that is too much |
08-29-2009, 03:46 PM | #11 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
|
Wow that isn't right. My diffs are 34.53mm to the outsides of the outer bearing races. That's fully assembled.
|
08-29-2009, 03:50 PM | #12 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| Thanks Bart I'll have to disassemble my axle to measure it But just one more drive b4 I do |
08-29-2009, 03:54 PM | #13 |
I wanna be Dave Join Date: Jan 2006 Location: Iowa, the antirecreation state!
Posts: 2,227
| you betcha |
08-30-2009, 04:39 PM | #14 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| |
09-04-2009, 02:53 AM | #15 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| |
09-04-2009, 01:30 PM | #16 |
RCC Addict Join Date: Nov 2008 Location: Greece, sun, sea and rocks
Posts: 1,242
|
Get a kyosho diff case. Most probably that will solve your problem.
|
09-05-2009, 12:37 PM | #17 |
Rock Crawler Join Date: Sep 2007 Location: Denmark
Posts: 904
| I might just get a complete savage flux diff |
| |