|
| LinkBack | Thread Tools | Display Modes |
06-18-2017, 07:37 AM | #1 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Orlandoo crawling on diy course Last edited by Dody dee; 06-18-2017 at 07:49 AM. |
Sponsored Links | |
06-20-2017, 10:10 AM | #2 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course |
06-20-2017, 11:22 AM | #3 |
I wanna be Dave Join Date: Aug 2016 Location: Orange County, CA
Posts: 3,643
| Re: Orlandoo crawling on diy course
Nice vids. Looks like yours doesn't pulse. Did you do anything to fix the pulsing, or just lucky?
|
06-20-2017, 01:21 PM | #4 | |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course Quote:
I don't know what pulsing is. After finished assembly, I found deformation on front & rear axle. Also the model not running smooth. I fix it with adjusting the rod like manual book says. I also adding sheet of tin on the all 4 wheels. Also adding on the front (servo place on chassis). I installed the steering servo on axle. For the shock, i extend the length of the shaft by changing the original with mini servo long screw. Added about 3mm longer. Many adjustment needed. But for now, i enjoying running this model first. | |
06-20-2017, 02:10 PM | #5 | |
I wanna be Dave Join Date: Aug 2016 Location: Orange County, CA
Posts: 3,643
| Re: Orlandoo crawling on diy course Quote:
Basically the pulsing I'm talking about is that the truck moves in a very jerky motion. The rotation of the axles weren't very smooth, so that the car when driven went goooooo..gg...goooooo..gg...go | |
06-20-2017, 02:30 PM | #6 | |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course Quote:
Where you put your servo? At first, i mount the servo on the chassis. But i see the problem when installing servo on the chassis. When the the shock depress, the front wheels turn to one side. Also when i turn to full left or right, the axle moves. The problem gone when i install the servo on axle. | |
06-21-2017, 05:53 AM | #7 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course Last edited by Dody dee; 06-21-2017 at 05:56 AM. |
06-22-2017, 05:42 AM | #8 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course Last edited by Dody dee; 06-22-2017 at 05:47 AM. |
06-22-2017, 09:24 AM | #9 |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: Orlandoo crawling on diy course
I still have mine unassembled in it's box with all the electronics, too. Now I need to get busy with it.
|
06-22-2017, 12:50 PM | #10 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course |
06-22-2017, 01:41 PM | #11 |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: Orlandoo crawling on diy course
I was looking at a few different bodies. One in particular is an Ertl wrecker that similar to the one in the Cars movie/cartoon. I just need to get some measurements before I get into it.
|
06-22-2017, 02:15 PM | #12 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course |
06-22-2017, 05:05 PM | #13 |
I wanna be Dave Join Date: Jul 2014 Location: Deep South
Posts: 3,444
| Re: Orlandoo crawling on diy course
That looks like it. The one I was fondling wasn't diecast though. It was plastic and a pull back type toy. The hook was on a long elastic cord.
|
06-25-2017, 10:15 AM | #14 |
Newbie Join Date: Jun 2017 Location: Indonesia
Posts: 10
| Re: Orlandoo crawling on diy course |
Orlandoo crawling on diy course - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Orlandoo | wheatyman | Micro Scale Rigs | 29 | 04-26-2017 01:28 PM |
Unboxing my Orlandoo 1:35 | HB RC | Scale Videos! | 0 | 04-21-2017 04:44 PM |
My Orlandoo 1:35 | HB RC | Micro Scale Rigs | 0 | 04-21-2017 04:43 PM |
New Orlandoo | Joostproost | Micro Scale Rigs | 1 | 09-07-2016 10:48 AM |
| |