| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
12-16-2015, 08:40 AM
| #1 |
| Pebble Pounder Join Date: Oct 2006 Location: Montreal
Posts: 199
|  Driveshaft length for Gelande 2 and TF2
Would an 82-117mm shaft be acceptable for the Gelande/TF2 center drive line? I know the TF2 is a little longer. These are the ones I'm looking at: Hardened Universal Shaft (82-117mm) 5mm hole [J90031] : JunFac.com Thanks! |
|  |
| Sponsored Links | |
| | |
|
12-16-2015, 09:53 AM
| #2 |
| RCC Addict  Join Date: Feb 2014 Location: Mt. Juliet, TN
Posts: 1,031
| Re: Driveshaft length for Gelande 2 and TF2 |
|
| |
|
12-16-2015, 10:45 AM
| #3 |
| Pebble Pounder Join Date: Oct 2006 Location: Montreal
Posts: 199
| Re: Driveshaft length for Gelande 2 and TF2
I had seen that chart but they list several shafts with different sizes as working. The reason I want the 82-117mm ones is that my LHS has them on sale. I notice in the chartt hat they say Z-S0583 is compatible both front and rear on both trucks and that one is 89-120mm so I can't imagine that 3mm would make a huge difference, but I wanted to check with you guys as I don't have the truck in hand yet so I cannot measure.
|
|
| |
|
12-16-2015, 10:51 AM
| #4 |
| Pebble Pounder Join Date: Oct 2006 Location: Montreal
Posts: 199
| Re: Driveshaft length for Gelande 2 and TF2
Also when they give shaft measurements, is the extended number with the shafts end to end but not interlocked? Or does it mean there is enough engament remaining at that length for full strength (ie. operating at 117mm is still acceptable)?
Last edited by norco kid; 12-16-2015 at 10:53 AM. |
|
| |
|
12-16-2015, 11:03 AM
| #5 |
| Rock Stacker Join Date: Dec 2015 Location: Finland
Posts: 50
| Re: Driveshaft length for Gelande 2 and TF2
I've been using those JunFac shafts succesfully in my G2 D90 rig. They are a good choice.
|
|
| |
|
12-16-2015, 07:25 PM
| #6 |
| Pebble Pounder Join Date: Oct 2006 Location: Montreal
Posts: 199
| Re: Driveshaft length for Gelande 2 and TF2
Thanks for the help guys, it looks like the 82-117mm shafts are good for the G2 front and rear and the front for the TF2. The rear TF2 shaft needs to be a little longer.
|
|
| |
|
12-17-2015, 11:31 AM
| #7 | |
| Pebble Pounder Join Date: Oct 2006 Location: Montreal
Posts: 199
| Re: Driveshaft length for Gelande 2 and TF2 Quote:
| |
|
| |
|
01-04-2016, 02:50 PM
| #8 | |
| Rock Stacker Join Date: Dec 2015 Location: Finland
Posts: 50
| Re: Driveshaft length for Gelande 2 and TF2 Quote:
 | |
|
| |
|
01-07-2016, 06:22 PM
| #9 |
| Rock Crawler Join Date: May 2009 Location: Welderville just south of benchviseland
Posts: 634
| Re: Driveshaft length for Gelande 2 and TF2
I just put a set of shorty Mip's meant for a 4wd Traxxas on my G2 Cruiser. Not the "slimmest" option by any means, but they fit like a glove and they're not going to break.
|
|
| |
|
Driveshaft length for Gelande 2 and TF2 - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Unlimited rubicon stock driveshaft length? | TrimbleTractor | Axial SCX-10 | 0 | 03-03-2015 09:12 AM |
| TF2 driveshaft length | Lentsnh2012 | RC4WD Trail Finder 2 | 9 | 06-16-2013 01:45 PM |
| Pick up body and driveshaft length | monkeyracing | Tamiya XC/CC01 | 9 | 06-01-2012 10:21 PM |
| MPI driveshaft length | MudboyNJ | Losi Mini-Rock Crawler | 3 | 09-28-2011 05:34 AM |
| Driveshaft Length | 02hawk | Axial SCX-10 | 0 | 03-11-2011 03:18 PM |
| |
Linear Mode
