03-28-2017, 07:43 PM | #1 |
Newbie Join Date: Mar 2017 Location: Nova Scotia
Posts: 11
| Steering knuckles
I broke the steering knuckle of my rs10 xt. The local hobby shop does not support parts. Will the one from scx10 fit without modification?
|
Sponsored Links | |
03-28-2017, 08:16 PM | #2 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles
Post a pic from that i told you what can you do Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:16 PM | #3 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles
You can use the terminals with a steel rod Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:21 PM | #4 |
Newbie Join Date: Mar 2017 Location: Nova Scotia
Posts: 11
| Re: Steering knuckles |
03-28-2017, 08:23 PM | #5 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:28 PM | #6 |
Newbie Join Date: Mar 2017 Location: Nova Scotia
Posts: 11
| Re: Steering knuckles
So are those the axial knuckles? Hard to tell from the picture..... just want to know if axial knuckle will fit cause it's what the local hobby shop sells.
|
03-28-2017, 08:30 PM | #7 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles
No they are from rs10 Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:35 PM | #8 |
Newbie Join Date: Mar 2017 Location: Nova Scotia
Posts: 11
| Re: Steering knuckles
I'm asking about the steering knuckle, not the steering link.
|
03-28-2017, 08:55 PM | #9 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles
Ups my bad Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:56 PM | #10 |
Newbie Join Date: Jan 2013 Location: Dominican Republic
Posts: 46
| Re: Steering knuckles
Upload a photo from the problem Enviado desde mi SM-N900P mediante Tapatalk |
03-28-2017, 08:56 PM | #11 |
Newbie Join Date: Sep 2016 Location: Tacoma
Posts: 17
| Steering knuckles
Yes they will. But you might have to loose one of the bearings or the will bind up.
|
03-28-2017, 09:05 PM | #12 |
Newbie Join Date: Mar 2017 Location: Nova Scotia
Posts: 11
| Re: Steering knuckles
So it's ok to run with just one bearing without wobble?
|
03-28-2017, 10:26 PM | #13 |
Newbie Join Date: Sep 2016 Location: Tacoma
Posts: 17
| Re: Steering knuckles I read somewhere, is this forum I think, that they did with no issues but I did the universal mod and dremeled out the inside bearing area to get the bearing in deeper so it would turn without binding. I didn't try it with the stock dog bones. I did go with BTA steering because of the bad Ackerman effect. The inner wheel was turning less than the outer so it pushed real bad. Going BTA fixed this. I think different knuckles would do the trick also I think. Sent from my iPhone using Tapatalk |
Steering knuckles - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Steering/Alignment Problem After Install RPM Steering Knuckles? | Barzan724 | Newbie General | 2 | 01-21-2016 06:32 PM |
Best steering knuckles | Sergio Neyra Up | Axial AX-10 Scorpion | 15 | 02-17-2010 07:01 AM |
Hot Racing Steering knuckles - more steering than the original plastic ones? | Tomy | Axial AX-10 Scorpion | 1 | 11-16-2008 11:26 AM |
steering knuckles | rash_powder | Tamiya Clod Buster | 8 | 01-02-2007 08:19 AM |
steering knuckles | rockmike | Tamiya TLT Crawlers | 4 | 08-08-2006 12:59 PM |
| |