04-30-2011, 11:20 AM | #1 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
| my RTI ramp
so i've been working on an RTI ramp for quite a while, just havent found time to work on it so its been slow going. but right now i got one angled piece notched and is ready to be welded on. i figured i'd grab some pics before i tacked it on so i came in to grab the camera so in a little bit it should be done minus the paint. will be back in a little bit with pictures.
|
Sponsored Links | |
04-30-2011, 12:10 PM | #2 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
got the angled pieces welded on and tested it out, still needs some expanded metal. im also surprised on how stable it is it slids around a little on the shop floor but it wont tip. its getting painted john deere green just to be different and plus i have some. here's some pictures. |
04-30-2011, 02:12 PM | #3 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
got the expanded metal welded on.. looks pretty good to me.... i will get some more pics soon.
|
05-09-2011, 09:09 PM | #4 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
got it painted up and it was sitting on some cardboard which was sitting on a bucket in the yard drying, not 10mins after painting it my cousin plows into the bucket with his rc car knocks the ramp into the dirt.... lots of swearing and yelling the paint job was fawked and i tossed it across the yard because i was pissed off. so needless to say i have to sand the whole thing down and repaint it, but i will get some pictures of it tomorrow before i do that. EDIT:found some pictures of it after i got the expanded metal on. Last edited by AX10wannabe; 05-09-2011 at 09:12 PM. |
05-09-2011, 10:09 PM | #5 |
Rock Crawler Join Date: Jun 2008 Location: South Ogden, Utah
Posts: 678
|
very cool, looks burly |
05-09-2011, 11:04 PM | #6 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
thanks its nice to have it done finally.
|
05-13-2011, 01:13 PM | #7 |
Rock Crawler Join Date: Mar 2009 Location: Alvin,Texas
Posts: 820
|
Nice ! Can you give me some measurements on it .? |
05-13-2011, 07:38 PM | #8 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
i'll have to measure it, but i know the height to the highest point is 7"-7 3/4" and its somewhere in the 13-14inch long range. dont quote me on these measurements i will take a tape to it for ya! EDIT- just ran out to the shop and grabbed some measurements.. 7 1/2" high total 12" long angled part is 13 1/2" long 3" wide also made of 1/2" square tubing hope that helps ya out!!! Last edited by AX10wannabe; 05-13-2011 at 07:46 PM. |
05-14-2011, 06:01 AM | #9 |
Rock Crawler Join Date: Mar 2009 Location: Alvin,Texas
Posts: 820
|
It does , think this is my weekend project. Thanks, |
05-15-2011, 11:24 AM | #10 |
RCC Addict Join Date: Jun 2009 Location: Salmon Arm BC
Posts: 1,777
|
haha no problem. post up some pics when you get it done! |
| |