| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
01-08-2017, 09:08 AM
| #1 |
| Quarry Creeper Join Date: Nov 2016 Location: Surrey
Posts: 462
|  Cr-01 carbon steel shafts
I installed the carbon steel prop shafts to my CR-01 thinking it'd be the most reliable option. Well, one of them is fine but the other lasted 45 minutes before it lost one of its cross joints. Does anyone know if cross joint assembly part number 53500 is compatible? I didn't want to fork out another £30 for a full complete shaft when there's nothing wrong with it. |
|  |
| Sponsored Links | |
| | |
|
01-08-2017, 09:26 AM
| #2 |
| RCC Addict Join Date: Sep 2008 Location: Philadelphia, PA
Posts: 1,048
| Re: Cr-01 carbon steel shafts
Did you just lose the pin? sent from Galaxy Note4 using Tapatalk |
|
| |
|
01-08-2017, 09:42 AM
| #3 |
| Quarry Creeper Join Date: Nov 2016 Location: Surrey
Posts: 462
| Re: Cr-01 carbon steel shafts
I lost the little pin - the grub screw must have come loose even though it was thread locked. Once the pin was out it spat out the centre part with the grub screw as well. Was in a very leafy area of the woods so absolutely no chance of finding it :(
|
|
| |
|
01-08-2017, 11:06 AM
| #4 |
| RCC Addict Join Date: Sep 2008 Location: Philadelphia, PA
Posts: 1,048
| Re: Cr-01 carbon steel shafts
Those pins are a fairly common part. I lost that once and found out I had a few spares from other kits. After losing one, now I have a thin strip of black tape around the hub so the pin can't fall out if it ever gets loose sent from Galaxy Note4 using Tapatalk |
|
| |
|
01-08-2017, 12:07 PM
| #5 |
| Quarry Creeper Join Date: Nov 2016 Location: Surrey
Posts: 462
| Re: Cr-01 carbon steel shafts  The shaft came out and I lost the cross joint too |
|
| |
|
01-08-2017, 12:10 PM
| #6 | |
| Quarry Creeper Join Date: Nov 2016 Location: Surrey
Posts: 462
| Re: Cr-01 carbon steel shafts Quote:
That's a good idea. I'll put a blob of threadlock and tape over it. I just need to source the cross joint and grub screw. | |
|
| |
|
01-10-2017, 07:41 AM
| #7 |
| Quarry Creeper Join Date: Nov 2016 Location: Surrey
Posts: 462
| Re: Cr-01 carbon steel shafts  Just in case somebody is unsure, this part number is correct. Shaft fixed  |
|
| |
|
Cr-01 carbon steel shafts - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Carbon steel drive shafts | KOH | G-Made Crawlers | 9 | 10-23-2016 11:27 AM |
| G Made Hardened Carbon Steel Universal Shafts | desertdude | Axial Wraith | 6 | 02-10-2016 07:42 PM |
| Junfac Hardened Carbon Steel Drive Shafts? | STANG KILLA SS | Axial SCX-10 | 20 | 06-10-2011 08:54 PM |
| Tamiya carbon steel propeller shafts out now | Bok | Tamiya CR-01 | 7 | 12-24-2008 05:52 AM |
| |
Linear Mode
