awsome thanks man i been waiting for a great reaction lol i think it looks much better to


but im waiting on electronics which should be here tommorow!!! and i still need yokes and shafts

any one els?

Well i got my crawler done today maxx shafts and seem to be doing pretty good with em havent slipped off yet i just have set screws on the tlt pinions and my g hawgs seem to do pretty good i thought i will hopfully have some pics up soon!!!

OK snapped a few pics not in action though sorry and i got a problem i didnt drill my pinion on the axle but its seems to work fine has not fallen off yet but the yoke is not on straight and when i drive it seems to wobble back and forth the yoke is on there nice tight though is this a problem???


heres the pics and yes the battery pack is in the back of my rig it wont mount up front with out messes my flex up but it dousnt seem to wanna tip back that much at all also i gotta pretty ghetto mounting system going on lol dont make fun of it

http://i34.photobucket.com/albums/d1...x/100_1766.jpg

http://i34.photobucket.com/albums/d1...x/100_1767.jpg

http://i34.photobucket.com/albums/d1...x/100_1776.jpg

http://i34.photobucket.com/albums/d1...x/100_1780.jpg

Nice Bulid!!!!! Like The Body And Paint Job.maybe U Should Try Puting A Washer In Between The Yoke And Axle

yea not a bad idea

any one esl any ideas i think i may just leave it

Go back and drill the holes, the set pins will eventualy slip off under load.

hmm they havent slipped off yet though

i think you are a bit high

check this pic hoe the chasis is just over the height of the tires

http://www.xtreme-rc-hobbies.net/images/Image18.jpg

cog is very important

seems to do fine though

hey you are asking for advice right ? chivas and i have both been through the whole xrc setting up deal, so if you feel that your setup works for you, and if you are happy with it that's all that counts"thumbsup" .... until you put it up against an xrc that is correctly dialed in;-)

thanks to mascman for his post i got the maxx shafts taht i had lying around on the Chivas Jeep

these are the tools i used and before and after pics

the stones i sthe exacts size of the tlt stock drive cup and the other grindy thingy is a perfect match to drill the hole for the pins that holds the cup in the yoke, the gribder is used for the tranny side yoke

http://laredocp4x4.casanovaspeedshac...d/DSC02805.jpg

this is a pic of the other side of the yoke with the cup inside and pin also. for me it was easier to put the cup inside the yoke first and once it's in place dremel the hole for the pin thru the pin hole of the yoke with the cup inside. remeber no to let any of the cup protrude from the ujoint side or you will bind

http://laredocp4x4.casanovaspeedshac...d/DSC02807.jpg

here is the pic of one side of the tranny the pin goes straight thru as the tranny mount has a predrilled hole

http://laredocp4x4.casanovaspeedshac...d/DSC02809.jpg

here is the spur side this part had to do a little mod to the tranny case

http://laredocp4x4.casanovaspeedshac...d/DSC02810.jpg

rear conected

http://laredocp4x4.casanovaspeedshac...d/DSC02811.jpg

front conected

http://laredocp4x4.casanovaspeedshac...d/DSC02812.jpg

tranny mounted and conected top view

http://laredocp4x4.casanovaspeedshac...d/DSC02813.jpg

i dont have enough set screws

what are those ? ? ?

the long ones with thread on on the hex end ? ? ?

i have some extra ones i think i can dig up and send them to ya

i dont know what ever ones u use to hold on the tlt yoke

you mean the set pins? they should come with the yokes.

yes taht is correct they come with the traxxas yokes

well i did it seems to work fine but i messed up one of those tlt yokes and i drilled my pinion about half way so the set screw will sit inside the pinion a little bit it seems to be on good n tight and straight but i just messed up one tlt yoke so i guess i will have to findanother