| |
06-09-2009, 03:06 PM
| #1 |
| That Was Totally Ninja!   Join Date: Mar 2004 Location: Whore Island
Posts: 3,062
|  7.2v out of the question... A customer bought a CC, and transfered his AX10 setup over to it. 55T novak, Mini-crawler 6-cell Nimh, Novak Rooster crawler. It stalls out horribly when under load, like trying to crawl up a wall. (It wont do it.) That's with an 18 tooth. Just tried a 12 tooth, and it's better for a few minutes until the NImh gets low, then is stalls again, but it's almost too slow to crawl. With a 2 cell Lipo and that se5tup it was better, but still too slow. I guess it's not possible to run that low of voltage with this truck and expect to have any wheelspeed? At least with a lathe motor... |
|  |
| Sponsored Links | |
| | |
|
06-09-2009, 03:16 PM
| #2 |
| Power of the Portals  Join Date: Feb 2004 Location: where ever the wind fawkin blows me, tx
Posts: 4,574
| Would different gear ratio in the axles help ? |
| |
|
06-09-2009, 03:50 PM
| #3 | |
| Losi Factory Pilot   Join Date: Feb 2007 Location: Chucking rocks at your little truck!
Posts: 1,276
| Quote:
| |
|
| |
|
06-09-2009, 06:40 PM
| #4 |
| Rock Crawler Join Date: Nov 2008 Location: I don't think theres rocks in Florida
Posts: 912
| I tried running a 7.2v 1650ma 2/3a pack thru Mamba max to a HH 5t. It was a joke. I don't even know why I tried that battery, it just isn't realistic. We need that high release/burst rate battery. This thing is power hungry. Still figuring out the power combination myself, and reading what everyone else has to say |
|
| |
|
06-09-2009, 06:49 PM
| #5 |
| Rock Crawler Join Date: Apr 2009 Location: NorCal
Posts: 529
| Hummm,,i had a rooster crawler esc and a 55t with a 2S 1600mah 7.4 volt pack and got good times, decent wheel speed and not to bad heating the motor up,,,I was conservative in my driving but it had torque |
|
| |
|
06-09-2009, 07:02 PM
| #6 | |
| Gold Star Baby!   Join Date: Jun 2005 Location: In Kahoots!!!!!
Posts: 4,761
| Quote:
| |
|
| |
|
06-09-2009, 07:07 PM
| #7 |
| I wanna be Dave Join Date: May 2006 Location: AZ - In The 928
Posts: 4,425
| Anyone try running a 21t pinion or larger with a slower motor like a 55t yet? |
|
| |
|
06-09-2009, 07:13 PM
| #8 | |
| Rock Crawler Join Date: Apr 2009 Location: NorCal
Posts: 529
| Quote:
 | |
|
| |
|
06-09-2009, 08:50 PM
| #9 | |
| I wanna be Dave Join Date: Sep 2006 Location: Stuck on a Rig in the middle of nowhere Utah.
Posts: 2,054
| Quote:
| |
|
| |
|
06-09-2009, 10:18 PM
| #10 | |
| I like to #*&^ Join Date: Mar 2009 Location: sittin in the sky
Posts: 4,388
| Quote:
| |
|
| |
|
06-10-2009, 08:59 AM
| #11 | |
| That Was Totally Ninja! Join Date: Mar 2004 Location: Whore Island
Posts: 3,062
| Quote:
Customer decided to buy a Goat to solve his problems..  | |
|
| |
|
06-10-2009, 09:58 AM
| #12 | |
| Gold Star Baby!  Join Date: Dec 2008 Location: ZETROC
Posts: 206
| Quote:
11.1 lipo sidewinder 55 turn lathe and 20 , 18 , 14 tooth pinions  I WANT TO BUT THAT BRUSHLESS SENSORED SYSTEM BUT CANT DECIDE BETWEEN THE 21.5 TURN AND THE 17.5 TURN ANY ADVICE? | |
|
| |
 |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
