Re: Robbobs bored and building a shafty If you're still playing with the steering design...putting the tierod bta is of small advantage. You can run a front tie-rod bent so it fits just below the servo plate and above that round pinion shaft cover. Virtually totally out of the way. But somehow getting the steering horn/drag link bta would be a big deal. That's what sticks out and hits rock. It's on my someday list. |
Re: Robbobs bored and building a shafty Quote:
The servo arm BTA would be great (and do able) I just don't like the cosmetics of it all. Ya I like it all to look good too lol :mrgreen: |
Re: Robbobs bored and building a shafty any updates on this rig? asking for a friend. |
Re: Robbobs bored and building a shafty Quote:
That would be a negative sir ..... Ran it, broke the weld on my front axle then parked it when the un-Stuck came up. |
Re: Robbobs bored and building a shafty Ok so now Ive got updates :mrgreen: Ive been stalled on this truck for sometime, it was just to many projects and not happy with my front axle. Now thats fixed and been fun getting things together on it. So been following along with CodyBoy on his front axle conversion and got lucky enough to get my hands on one early. http://i208.photobucket.com/albums/b...psfujmz19z.jpg Couple hours of adding my touch to everything and putting it all together I had this http://i208.photobucket.com/albums/b...psht1udem6.jpg http://i208.photobucket.com/albums/b...pshuyxwqxn.jpg And after figuring some front upper and lower links out ...... I was sitting with a stander http://i208.photobucket.com/albums/b...psinznu0cs.jpg http://i208.photobucket.com/albums/b...psm15ecrto.jpg Two things Im gonna try on this. First one is a Tekin B1r esc, yes I know its probably gonna blow up but its worth a shot. I ran these in the beginning of my MOA days on 13T Crawlmasters and 3S with no problems. So decased and rewired it fits nicely in the skid. (damn cap is too big for under the aaxle plate) The second thing is Im trying our Insidious transmission again. When I ran it in my AX sporty it just didnt feel like it was low enough. I always felt like I had no low end ooomph from it even with some stought motors. It ran like a wraith running U4 lol so with the worms Im hoping it will be a better match. It is heavier then the LNC tranny but worth a try. http://i208.photobucket.com/albums/b...psvzsqrlcl.jpg So there she sits for a couple weeks. Have to finish wiring everything up and get some rubber under her plus a few loose ends. And our weather just went from 40s to SNOW and now back to 40s so we'll see what mother nature says when its done. "thumbsup" |
Re: Robbobs bored and building a shafty Looking nice Bob, I sure hope these axles work out! I think alone there are some weak spots, but when it is all tied together it becomes a pretty solid unit. Are you going to hang some more weight on the front? Once I get these first five done I think I will build one for me before I start offering these."thumbsup" Ernie |
Re: Robbobs bored and building a shafty Quote:
|
Re: Robbobs bored and building a shafty So your trans different ratio from the lnc trans? |
Re: Robbobs bored and building a shafty Quote:
reason being.. my freestyle trans is too big as well as a ax10 trans. I do believe I have room for a reduction unit though. |
Re: Robbobs bored and building a shafty Quote:
LNC is 1.2:1 i think or was that the LCC? |
Re: Robbobs bored and building a shafty Just a couple more pictures now that she is up and running. And Im looking to hit my goal with a few changes to equipment and steel pieces for aluminum. http://i208.photobucket.com/albums/b...pskqbpkjbq.jpg http://i208.photobucket.com/albums/b...pssmaaimqj.jpg Threw a bubbled top roof body on to be legal for now and it all comes together http://i208.photobucket.com/albums/b...pse8o0pggs.jpg http://i208.photobucket.com/albums/b...ps87uu81pz.jpg Im liking the bias even with out the battery on the front axle "thumbsup" http://i208.photobucket.com/albums/b...psy8akkrrk.jpg Practice Tuesday "thumbsup" "thumbsup" |
Re: Robbobs bored and building a shafty What body is that? |
Re: Robbobs bored and building a shafty Quote:
JConcepts Illuzion with a bad bubbled roof to make it legal ......... |
Re: Robbobs bored and building a shafty Quote:
LNC Ratio: 2.27 to 1 LCC Ratio: 1.33 to 1 |
Re: Robbobs bored and building a shafty Dang Bob. Sometime makes me wish our group still comp. |
Re: Robbobs bored and building a shafty Quote:
Quote:
Thanks man ...... you should start it up again, build and they will come? :mrgreen: |
Re: Robbobs bored and building a shafty Hey Bob, I have been thinking about motor, esc and gearing for my Losi. I have a Holmes Revolver S stubby 540 2000kv I have been hoarding for a couple years for this build. It is 100 grams lighter than a Tekin 13.5, what do you think. Good, bad? What esc? Or should I just send it to you for your tranny?:ror: Ernie |
Re: Robbobs bored and building a shafty Quote:
Im interested in how that motor could work, just read his site and didnt know it was sensored. I would try it, I think it could actually work well. :mrgreen: Im a Tekin fan for brushless crawling and for some racing but I dont know how that would pair up with his motor. Im betting Castle and Holmes ESC's would be the better ticket but theyre all about double the size of a Tekin. |
Re: Robbobs bored and building a shafty I know it scaler. But maybe it will get the gears turning. http://www.rccrawler.com/forum/1-9-s...-comp-rig.html |
Re: Robbobs bored and building a shafty The momba micro X is a power house and small |
All times are GMT -6. The time now is 05:53 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com