Re: TRX4 wheel fitment info
 

I have the proline faultline wheels and the inner beadlock ring needs to be enlarged to gain clearance to the portal covers. Also I installed MIP 4mm axle extensions for additional clearance.

Re: TRX4 wheel fitment info
 

so with the rc4wd hex adapters i used the wheels fit but when i tighten the nut down its bottoms out on the threads and the wheels are a little loose. Like a couple thousandths of an inch of movement at most probably but its there.....do I run a washer behind the nut?! Do i need wider hexes? I didn't see anyone mention this particular issue with the rc4wd steel wagon wheels.

Re: TRX4 wheel fitment info
 

I didn’t have that issue with mine but I would say a washer behind the nut would be a cheap easy fix


Sent from my iPhone using Tapatalk

Re: TRX4 wheel fitment info
 

I noticed when I took the pin drive adapter off to put the hex adapter on that the hex one is narrower than the pin drive.....when i put the wheels on and look at it you can see the end of the threads are right at the face of the wheel

Re: TRX4 wheel fitment info
 

I noticed certain nuts go down further on the stub than other as well as using washers. Or you could take a flare nut make the smallest counter sink you can and re thread it. Havent tried it but I think it would work.

Sent from my SAMSUNG-SM-G920A using Tapatalk

Re: TRX4 wheel fitment info
 

I ended up replacing the stock Traxxas wheel hexes with rc4wd part #Z-S1844 and everything is perfect now. I was under the assumption that I could just change from pin drive to hex drive on the back of the wheel and use the stock hexes but they were too narrow

Re: TRX4 wheel fitment info
 

Re: TRX4 wheel fitment info
 

That’s all I had to do was get the adapters for the back of the wheel


Sent from my iPhone using Tapatalk

Re: TRX4 wheel fitment info
 

with rc4wd wagon wheels? look very closely at the wheel face around the nut...wiggle it slowly and look closely....it very well may be loose and maybe you didn't notice....it's a very minute amount of looseness....probably a couple thousandths of an inch of movement or so but it's there and I can't imagine I'm the only one......unless I got something that was machined improperly or something strange like that....

Re: TRX4 wheel fitment info
 

also, I did not have to drill out the center hole at all for the wheel to fit on all the way like a few other people said they had to so there's that too.......

Re: TRX4 wheel fitment info
 

What width slw hubs with vanquish wheels
Is closest to stock?

Re: TRX4 wheel fitment info
 

These should fit, right? 46.5 mm inner diameter in the back, and they show it fitting the Wraith.

https://store.rc4wd.com/Rally-19-Bea...ls_p_5691.html

Re: TRX4 wheel fitment info
 

Should be no problems. Looks like they'll clear the portals and the hex is fine.

Re: TRX4 wheel fitment info
 

MOHERO Silver wheels
https://www.amazon.com/gp/product/B0...0?ie=UTF8&th=1
DO NOT fit TRX-4 stock. Pretty serious rub on both front and back.

Some brass Treal +3mm hexes were perfect. Stance is very sexy, just a hair wider than the stock tires sat.

Editting in some nonsense so googlers might stumble across this post:

Amazon cheap mohero trx-4 trx4 mohero wheels traxxas wheel fitment mohero fitment Mohero wheels fitting trx-4 do mohero wheels fit traxxas?

Re: TRX4 wheel fitment info
 

Also, I have gone through this thread pretty carefully and haven't seen this chart posted yet. i found it on RC4WD and it seems like an excellent quick reference for wheel specs:

https://www.beadlok.com/wheel.pdf

Re: TRX4 wheel fitment info
 

Anyone know if these will clear the portals and some CODYBOY wheel weights? Really like the look of them.
https://m.ebay.com/itm/1-9-Beadlock-...from=R40&rt=nc

Re: TRX4 wheel fitment info
 

Hey Justin, I would be careful buying any wheel with a rear beadlock ring. I know some of them out there with the rear ring will not fit over the portals. It's hard to tell by looking at the photos. "thumbsup"
Ernie

Re: TRX4 wheel fitment info
 

Thank you brotha!

Re: TRX4 wheel fitment info
 

Gmade MT1904 1.9 tires on INJORA beadlock (4PCS RC Rock Crawler Metal Wheel Rim for 1/10 )

https://www.aliexpress.com/wholesale...njora+beadlock

https://ae01.alicdn.com/kf/HTB11G.BR...pg_640x640.jpg

They fit perfectly and the bead locks are easy to assemble. Measures 121 * 45 mm
You just have to widen the outer hole rim 1 mm, from 5mm to 6mm

Tires Gmade MT1904 1.9
http://hobbyflor.es/WebRoot/Store14/...m70304_4_m.jpg

Re: TRX4 wheel fitment info
 

Without reading through stuff I honestly do not understand. I am a tad more confused now.
Is there a definitive list of direct fits? Maybe a list which requires a hub add on.


I am after some direct fit 2.2 wheels and tyres that I can buy without going too wrong. I do not run a body so no rubbing issues.