Locked UP's TRX-4 My most recent picture & specs: http://www.lockeduprc.net/misc/pictures/TRX4/0014.jpg http://www.lockeduprc.net/misc/pictures/TRX4/0010.jpg Traxxas TRX-4 frame & axle housings Front Axle: FI Spool, Black Steel Portal Covers, Black Steeel Portal Knuckles, Black Steel C-Hubs, Traxxas Overdrive gears Rear Axle: Traxxas Underdrive Gears Bearings: Stock Body: Proline Bronco Wheels: Locked Up RC 1.9" Heritage AO8 with Red Agile Rings. Tires: RC4WD 4.19" Baja Claws Hubs: Locked Up RC Ultra front & rear ESC: XL-5 Motor: Titan 550 Spur: 45t Pinion 11t Steering Servo: HS-7954SH Winch: Commando RTR Upgraded winch line: 200lb Synthetic Fairlead: Aluminum 1/10 Tow Strap: Locked Up RC Standard Shackle: 1:10 D Ring Shackles Snatch Block: Devil RC --------------------------------------------- THE BUILD: --------------------------------------------- Picked this up in a deal locally so it was "pre-loved" a bit. Came with the Bronco body on it and ... I'm sorta digging it. http://www.lockeduprc.net/misc/pictu...4/IMG_5676.jpg Front & rear Wheelbases are off a hair. Will work on those. http://www.lockeduprc.net/misc/pictu...4/IMG_5677.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5678.jpg The interior looks like a Deadbolt. Needs a haircut... http://www.lockeduprc.net/misc/pictu...4/IMG_5679.jpg Also a big vast nothingness in the back of the interior. http://www.lockeduprc.net/misc/pictu...4/IMG_5693.jpg The front bumper hangs down really low. http://www.lockeduprc.net/misc/pictu...4/IMG_5681.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5682.jpg Turtle shot http://www.lockeduprc.net/misc/pictu...4/IMG_5686.jpg Naked http://www.lockeduprc.net/misc/pictu...4/IMG_5687.jpg Swapped servo that came with it. http://www.lockeduprc.net/misc/pictu...4/IMG_5688.jpg |
Re: Locked UP's TRX-4 Immediately flipped the front bumper mount. Not perfect but better. http://www.lockeduprc.net/misc/pictu...4/IMG_5689.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5690.jpg Dropped front body mount one hole too. Good enough for now. http://www.lockeduprc.net/misc/pictu...4/IMG_5691.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5692.jpg I'm thinking 1/4" front and rear to remove form the WB will be good. http://www.lockeduprc.net/misc/pictu...4/IMG_5683.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5684.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5685.jpg |
Re: Locked UP's TRX-4 Not a Bomber interior - they have a driver & a co-driver. I think you may have a cut-out section from a Deadbolt tucked in there... |
Re: Locked UP's TRX-4 It will probably be easier to just shorten the rear not much room for movement up front |
Re: Locked UP's TRX-4 You need some LURC wheels:lmao::lmao::lmao: Good choice on car, they are better than a Axial"thumbsup" |
Re: Locked UP's TRX-4 Quote:
"thumbsup" For those wondering, the cage is held in with black sticky tape. It actually is a pretty decent way to get something better than open air into it. |
Re: Locked UP's TRX-4 Quote:
That should put the rear dead center in the wheel well. The front will still be a little bit forward in the well but it think it has to be for clearance when turning. Rear will easier for sure. That's just links. Front I will relocate the shock towers and everything back 1/4". That way it maintains the clearance between the draglink, tierod, etc. |
Re: Locked UP's TRX-4 You should think about the high-lift kit for it , when it comes out. |
Re: Locked UP's TRX-4 Quote:
I know that will be great from some people.... I did that on the H2 SCX10 with a homebrew setup. I actually had a 1:1 Bronco though and will be looking to make this a throwback of sorts. Funny that the color scheme is inverted! http://www.lockeduprc.net/misc/pictu.../myrtles21.jpg |
Re: Locked UP's TRX-4 I like the stretched look, the front end has a lot of scrub when turning so you'll have issues with the tires hitting the body when moving it back. |
Re: Locked UP's TRX-4 Quote:
"thumbsup" |
Re: Locked UP's TRX-4 Playing with the tire size a bit to figure out exactly what I'll need to tweak. http://www.lockeduprc.net/misc/pictu...4/IMG_5717.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5718.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5719.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5720.jpg And a few shots of things compressed a little. http://www.lockeduprc.net/misc/pictu...4/IMG_5721.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5722.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5723.jpg Side shots for reference http://www.lockeduprc.net/misc/pictu...4/IMG_5724.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5725.jpg |
Re: Locked UP's TRX-4 Decided to go ahead and boil the tires off starting with the spare. The spare was factory glued and looked to be in the best shape. It also had less glue than the others. Trusty goodwill pots & pans... http://www.lockeduprc.net/misc/pictu...4/IMG_5726.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5727.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5728.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5729.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5730.jpg Took a total of 20 minutes per side and it came off fairly easily. The boiling makes the glue brittle so you can crack the tires off. It does still require some force but no tearing, no chemical, no burning vapors... so I call it a win. |
Re: Locked UP's TRX-4 Very slight bit of glue reside but it's easy to pick off with a thumbnail. http://www.lockeduprc.net/misc/pictu...4/IMG_5732.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5733.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5734.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5735.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5736.jpg Up next ... the other four... http://www.lockeduprc.net/misc/pictu...4/IMG_5731.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5737.jpg |
Re: Locked UP's TRX-4 The main 4 tires were a bit more of a bitch. Look like they had been previously removed and glued back on. I'm guessing the PO did this when he painted them. http://www.lockeduprc.net/misc/pictu...4/IMG_5738.jpg There was a lot more glue on them, so they required more boiling. the 4 that were glued back on... http://www.lockeduprc.net/misc/pictu...4/IMG_5739.jpg Compared to factory glue... http://www.lockeduprc.net/misc/pictu...4/IMG_5740.jpg The difference is obvious on the rims as well. http://www.lockeduprc.net/misc/pictu...4/IMG_5741.jpg Some spots I could not break off even with an hour of boiling. Ugh. http://www.lockeduprc.net/misc/pictu...4/IMG_5742.jpg If you look closely, you will also see the 4 that were glued again must have been putting off some sort of fumes form the glue because they have an odd white tint to them. http://www.lockeduprc.net/misc/pictu...4/IMG_5747.jpg Closeup of the white: http://www.lockeduprc.net/misc/pictu...4/IMG_5748.jpg Compared to stock glue job: http://www.lockeduprc.net/misc/pictu...4/IMG_5749.jpg |
Re: Locked UP's TRX-4 So.... http://www.lockeduprc.net/misc/pictu...4/IMG_5754.jpg And http://www.lockeduprc.net/misc/pictu...4/IMG_5751.jpg leads to http://www.lockeduprc.net/misc/pictu...4/IMG_5755.jpg And no more white: http://www.lockeduprc.net/misc/pictu...4/IMG_5760.jpg And next time I'll tell you why I sanded the faces off the rings. http://www.lockeduprc.net/misc/pictu...4/IMG_5761.jpg |
Re: Locked UP's TRX-4 I decided to add some new rings to the wheels. Fairly simple process that starts with sanding the original rings down to be a smooth surface. http://www.lockeduprc.net/misc/pictu...4/IMG_5770.jpg I removed enough material to get rid of the design, but still left some of the lip. When measured, my wheel bodies come to 25mm exactly. http://www.lockeduprc.net/misc/pictu.../IMG_5770b.jpg I could have cut them off entirely but didn't....yet. No particular reason. To get the bolt pattern, I just held an original SCX10 beadlock ring in place and took my time. http://www.lockeduprc.net/misc/pictu...4/IMG_5762.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5763.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5764.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5765.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5766.jpg You can use a LURC ring of course, I just had the SCX ring on hand for the first one and since it is already beat up a little, why not. http://www.lockeduprc.net/misc/pictu...4/IMG_5767.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5768.jpg The bolt pattern fits really well with the TRX4 stock wheels. http://www.lockeduprc.net/misc/pictu...4/IMG_5769.jpg |
Re: Locked UP's TRX-4 You could also drill out for a bunch of screws and make these "Easy Mount" ... but I opted to use some of our M2x1 screws instead. http://www.lockeduprc.net/misc/pictu...4/IMG_5771.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5775.jpg I think this looks killer! http://www.lockeduprc.net/misc/pictu...4/IMG_5774.jpg |
Re: Locked UP's TRX-4 Working on lots of stuff for this thing. oops... http://www.lockeduprc.net/misc/pictu...4/IMG_1196.jpg |
Re: Locked UP's TRX-4 Got the wheelbase "corrected". http://www.lockeduprc.net/misc/pictu...4/IMG_5956.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5957.jpg http://www.lockeduprc.net/misc/pictu...4/IMG_5958.jpg Details to come... :mrgreen: |
All times are GMT -6. The time now is 09:25 PM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com