Vanquish Incision Pro MOA Chassis

[tjb]

Originally Posted by CHRIZAD

Any specs/measurement from the skid plate where the tranny sits up to the cross braces? Just wondering if s3r dig will fit in there before ill get one.

Um, this is a MOA chassis, the axial one only has the brace on one side


http://www.vanquishproducts.com/vp-p...0-chass10.html




Just ordered one for my set of bully's looking forward to getting it. Looks top notch quality as always..

[dragit]

Originally Posted by tjb

Um, this is a MOA chassis, the axial one only has the brace on one side


http://www.vanquishproducts.com/vp-p...0-chass10.html




Just ordered one for my set of bully's looking forward to getting it. Looks top notch quality as always..

thats because it has to have room for the motor and trans to hang out. refer to this build to see what i am talking about
dragits VP Incision build..........

[Jeepial]

This chassis supposed to use 4" shocks?

[punkuup5150]

i had to limit mine by over an inch so for competion use no if your just building to have fun and get as much articulation as possible and dont care about wheelbase then yes it all depends on what you plan on useing the chassis for

[Szczerba]

Originally Posted by Jeepial

This chassis supposed to use 4" shocks?

I tried 4" shocks, way too much flex for a comp truck. as stated below, IMO. And that was just flexing it on the bench without tires.

Originally Posted by punkuup5150

i had to limit mine by over an inch so for competion use no if your just building to have fun and get as much articulation as possible and dont care about wheelbase then yes it all depends on what you plan on useing the chassis for

I am running the Losi .9's built at 3.6". Perfect for me and this chassis.

I am really liking this chassis with the berg axles.
Great construction, awesome skid and plenty of room. It has alot of adjustability too. I ran it the first time at a comp this past saturday and was really impressed. I am running it at about 3 1/4" GC and right at 12.4" wb.

[Jeepial]

I have a set of the Axial comp shocks,and if they wont work well I might have to go another route..

[Agama]

Those shocks will work. Just limit the inside of the shock with fuel line tubing or a spacer to get the length that you want. I am going with this chassis soon.

[Rockcrawler]

Guys, 4" shocks will work with this chassis. I dont think mine are limited at all, but I will check as soon as I get a chance.

If you have any questions that I might be able to answer, feel free to post up or PM me.


My build thread. I just got this chassis on my rig after Crawlapalooza and I love it.

Rockcrawlers Berg/enroute Build.......Finally.

[Rockcrawler]

Originally Posted by Rockcrawler

My build thread. I just got this chassis on my rig after Crawlapalooza and I love it.

Rockcrawlers Berg/enroute Build.......Finally.

I have been to 2 comps since I put this chassis on......and won both!

Thank you VP.

[BADASSPONY]

Originally Posted by Rockcrawler

I have been to 2 comps since I put this chassis on......and won both!

Thank you VP.

What shocks are you running with the chassis?Im looking into building a bully with this chassi. Feel free to pm info. This will be my first comp rig build.

[Rockcrawler]

Originally Posted by BADASSPONY

What shocks are you running with the chassis?Im looking into building a bully with this chassi. Feel free to pm info. This will be my first comp rig build.

I am running the Traxxas Big bores with white losi springs.

[OfnaJoe]

anybody running this chassis with a 6 cell nimh pack, I got a Rooster Crawler ESC and it wont handle a 3S lipo

[OfnaJoe]

Just ordered my Vanquish Incision Pro MOA Chassis today, can't wait to get it to start building

[OfnaJoe]

Well after getting the Vanquish chassis I wish I hadn't !
It's set up to triangulate to lower links, if you run straight links they hit the motors, I had to put the lower links on the outside of the chassis, and I was wanting to run 4in shocks too, but this chassis don't like them unless you limit them to about 3.5 in. And it don't like stock type Clod axles either, it look like it would work OK with either Berg's or Bully's. But the machine work is second to none. So now I guess I will go hunting some different axles and lower links are on the way, gonna to try RC Guys machined links with the shock holes in them, might give me some more articulation

[DwaneO]

I'm really liking the looks of this chassis.
What is the measurement between the link mounting holes on one of the side plates ?

[OfnaJoe]

51mm front to back on center

[Szczerba]

Originally Posted by OfnaJoe

Well after getting the Vanquish chassis I wish I hadn't !
It's set up to triangulate to lower links, if you run straight links they hit the motors, I had to put the lower links on the outside of the chassis, and I was wanting to run 4in shocks too, but this chassis don't like them unless you limit them to about 3.5 in. And it don't like stock type Clod axles either, it look like it would work OK with either Berg's or Bully's. But the machine work is second to none. So now I guess I will go hunting some different axles and lower links are on the way, gonna to try RC Guys machined links with the shock holes in them, might give me some more articulation

I thought the same thing about the 3.5" shocks. I was wrong. I am running 3.8" shocks and love them. Just slightly limited some 4" er's. Way better than the 3.6" i was running. Doesn't sound like much but way better. Getting about 65 deg of flex. Works good.

Just read you put clod axles under it. Opps. I am running bergs.

[Rockcrawler]

Originally Posted by OfnaJoe

Well after getting the Vanquish chassis I wish I hadn't !
It's set up to triangulate to lower links, if you run straight links they hit the motors, I had to put the lower links on the outside of the chassis, and I was wanting to run 4in shocks too, but this chassis don't like them unless you limit them to about 3.5 in. And it don't like stock type Clod axles either, it look like it would work OK with either Berg's or Bully's. But the machine work is second to none. So now I guess I will go hunting some different axles and lower links are on the way, gonna to try RC Guys machined links with the shock holes in them, might give me some more articulation

:?

Joe, this chassis is set up for Berg/bully axles. Are you trying to use this as a super chassis with the clod axles? I am running 4" shocks on my berg and they work perfect.

If you get berg axles, let me know and I will help you with the setup.

[OfnaJoe]

Not super, I'm running 2.2's, Getting Berg's soon.

[RcBro]

Just wanted to say, I just recently took the dive into MOA and with the help of some ORCRC top dawg locals I decided on this chassis. I'm glad I did, this thing flat out works and my finishing places have never been higher. I took 7th in the AWCC Qualifier #4 against some amazing drivers and I've never been so happy.