• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

IFS kit for Wraith

Such a clean and slick lookin conversion, very nice!! How does this measure up and compare if the rear is an SCX10 axle on 1.9s? Would love to buy one today!

Probably Sent Sitting On The Toilet...
 
HPI-Killer said:
Such a clean and slick lookin conversion, very nice!! How does this measure up and compare if the rear is an SCX10 axle on 1.9s? Would love to buy one today!

Probably Sent Sitting On The Toilet...
Click to expand...

thanks! you would have to space the rear tires way out or it would look funny
 
Last edited:
6mm vs. 5mm Shafts on 300m lockers:



EXO spools 5mm vs 6mm.jpg
 
Got my kit and electronic try working for the most part for axialfest. Now that I am home I can start yo fine tune it.
za4a7u6a.jpg


Sent from my LG-LS970 using Tapatalk
 
I went with the gcm last locker with a 5mm alen cut to length with mip shafts.

Sent from my LG-LS970 using Tapatalk
 
I have the BM spool but it doesn't work with the mip shafts, I had clearance issues with them hitting the rpm arms early. Was really limiting my articulation.

Sent from my LG-LS970 using Tapatalk
 
That's exactly why I'm wanting to order one of those beast 6mm spools for my yeti when it comes out. Pm'd and sent him an email off his website and so far no word. I'm thinking he's super busy

Sent from my SPH-L720T using Tapatalk
 
cdbresson said:
I have the BM spool but it doesn't work with the mip shafts, I had clearance issues with them hitting the rpm arms early. Was really limiting my articulation.

Sent from my LG-LS970 using Tapatalk
Click to expand...


This is an issue between MIP and RPM arms, mine do the same thing. Possibly if the tangs are longer it would help, but I haven't looked at it that closely yet. I may make another 5mm shaft that's longer and see if it helps. Or I will relieve arms at that spot.
 
Blue Monkey RC said:
the next batch of 300m spools will be going into production tomorrow. i plan to make (4) with 6mm, .236" shafts. please SPEAK UP if you want a set of 6mm spools or you will have to wait until the next production run.

i still have a few 4340/4140 blemished spools left (2 extra "speed holes"). $15 each.
Click to expand...

I would like a 6mm spool please.
 
just a ?
about your 6mm output locker.
most of the ring gears I've seen - only have 5mm pass thru hole on them,
do/will U have to bore out the ring hole to get that 6mm locker shaft to go thru the ring gear ??

I've try to bore out the hole in a HD ring gear - that was vary hard to do !!
 
the DMG said:
just a ?
about your 6mm output locker.
most of the ring gears I've seen - only have 5mm pass thru hole on them,
do/will U have to bore out the ring hole to get that 6mm locker shaft to go thru the ring gear ??

I've try to bore out the hole in a HD ring gear - that was vary hard to do !!
Click to expand...

Yes it would be no different than using SDS shafts. Just use a carbide burr on the dremel and you shouldn't have any issue.
 
You must log in or register to reply here.

Similar threads

A
Anybody have experience with the meus ifs kit?
Replies
3
Views
176
NWCT24CRAWL
N
rubiconrockkrawler
Enduro Builders Kit with IFS V1
Replies
11
Views
593
Gula
Gula
T
Tbrown's IFS2 SCX10II
Replies
9
Views
683
OSRC
OSRC
OSRC
OS's Random Projects
Replies
16
Views
639
OSRC
OSRC
T
Utron with some french flavour
Replies
7
Views
655
tuxstang
T
Back
Top