k20man's xr10

[k20man]

I know it sux, but its the nature of the beast. Its bullet proof or nothing. lol I think there were some bad gears out there, but the stockers just fail far too easily. The upgraded housing and motor plate will make it tougher as will hardened gears. The RC4WD gears are out- sold out. I think they've been up twice now. I ordered earlier this week while they were available. They'll be back.

I think I've destroyed 4-5 pair of stock Final drive/spool gears, 2 sets in one comp!

I know your getting some goodies, they'll help.

yeah that sucks I try to get the gear but they sold out, only got the plates and case I hope this get me throug the course for bit longer at least more them one pack !!!!!!:lmao:

 

[k20man]

look what I got in the mail yesturday vp goodies!!!

I put them in and nop more gear failer!!

 

[k20man]

well I guess no iven vp cant stop the gear feiler !!!!

I got rear gear strip again, I install all the vp goodies on the rear only and after 5 packs thru boooonn :shock: again and on the from all bone stock and still working lol !!!!!

whats next ?????

 

[Jeepkid]

Man, I just swapped out my stock gears for Rc4wd gears. Never had a failure on the stock gears, most be hit and miss with them. I had 90+hours on them and they are in great condition.

 

[k20man]

Man, I just swapped out my stock gears for Rc4wd gears. Never had a failure on the stock gears, most be hit and miss with them. I had 90+hours on them and they are in great condition.

yes man I gues it most be hit and miss!!! cux I seen other threads sayn they haven got not problen with it yet !!!! :roll:

 

[Tydl]

In the axle housing itself, I'd make sure you didn't screw through a bearing race. Its easy to mix up those screws on the rear upper link mount. Which gear(s) are you breaking.

 

[k20man]

In the axle housing itself, I'd make sure you didn't screw through a bearing race. Its easy to mix up those screws on the rear upper link mount. Which gear(s) are you breaking.

I am breaking the rear gear the stock with all the vp motor plate and case !!

 

[Tydl]

I am breaking the rear gear the stock with all the vp motor plate and case !!

I thought you got some hr gears? If your still running stock you need to get hardened gears, but it sounds like you have an actual problem. Check your bearings and check that no screws went thru bearing races. You shouldn't be busting gears so easily with the Vp housing and motor plate.

 

[k20man]

I thought you got some hr gears? If your still running stock you need to get hardened gears, but it sounds like you have an actual problem. Check your bearings and check that no screws went thru bearing races. You shouldn't be busting gears so easily with the Vp housing and motor plate.

yes wave something is not right!! Ill well take it apart to check it all and see why!! i understand the stock gear sucks but like that!! in the front is all good and everithing is stock !!!

 

[k20man]

update

I guess I am gething more adictic to this lol, well I got few things for my rig chassis,tires,gears,new electronics ill post pic later "thumbsup"

 

[k20man]

 

[k20man]

I got this chassis from harvo thanks

 

[k20man]

waiting for more to come in the mail cant waaaaaait :twisted:

 

[k20man]

I guess I going to be using the comm lathe !!

 

[richardgarrett56]

looks great man.nice lathe to:shock:

 

[k20man]

thanks richard"thumbsup"

 

[richardgarrett56]

what kind of chassis is that?

 

[k20man]

hellstrom from jpcustom!!

 

[richardgarrett56]

ok,i haven't seen one yet. looks cool"thumbsup"

 

[Vertec]

What are you using for your electronics tray?