Hello, I have lot of time reading this page and I recently registered and I decided to post.
First of all, I wanted to say I'm Spanish and do not speak English well, and the text is written with the translator of google, so excuse my bad English lol.
This is a project I have in mind for a long time, and I finally decided to start with, the base is an axial AX10 kit, hope you like:
Here I leave the creation of the project step by step.
MATERIALS:
-Axes axial
-tranny axial
-dig 3r
-dampers 3r
-winch 3r, even without putting
-Tires (the original one proline badlands and the current one MoAbs)
-wheels DNS
-Junfac-cardan front (because the rear is the dig because it is shorter)
-Servo 15 kg
-4ch transmitter futaba check the trigger as a check for one friend. I have not yet so I can not post pictures, I have not seen and I haha
-Rc4wd tube chassis
-and well what I will leave now forgotten nurse in the process of creation jejeje.
PROBLEMS
-The first problem I found when opening the box with the material, and I was surprised to see a shaft with the support of the links above party, to fix I made these formats:
Support broken
new anchors:
Forward
Back
Once solved this issue, I began to assemble, to have it finished.
-My second mistake was riding patella long on one side than another, so that the rear axle was 1cm more separated from the chassis on one side than the other, solve it by putting them in equal measures, the truth is that was a mistake the most awkward.
FEATURES
-One of the main features is the suspension, that I have pretty limited so that the car becomes more stable, is in my semidroop, and although it has a lot of suspension, it makes up with its high stability, with the weight of the tubular me his own cost. This was a very difficult decision to make lol because I like cars with great suspension, but I think you and found a middle ground for me like this to pm, here you have some photos with maximum articulation:
Lateral Stability
Vertical stability
-In height, the car will land at rest 6.5cm and 10cm estiraza even in the second picture is with the wheels without tires as it touches the ground so no undir suspension and can be displayed better headroom:
Repose
high
-Another feature that is barely noticeable, is that the back is longer than up front, but just 0.5cm or 1cm, and is also somewhat higher in back than up front, but not much in the first picture appears much higher back because it has the rear wheel up pliers jeje:
Before
Now
-The dig is to put it microserve do not know if this will be able to move it, if you say see it or I will not put a great servo and see if someone over there has proven to me, because I pushed the arm microserve and this pretty hard, I don´t know to force the pots have these
He has new shoes
and little more, now I've put a new configuration of links, is this (with links inside the chassis):
and I can only part of the electronics that I hope to finish soon.
The entire thread you can see it here, but is in Spanish:
http://www.zonacrawling.com/foros/viewtopic.php?f=3&t=8024
I hope you enjoy
First of all, I wanted to say I'm Spanish and do not speak English well, and the text is written with the translator of google, so excuse my bad English lol.
This is a project I have in mind for a long time, and I finally decided to start with, the base is an axial AX10 kit, hope you like:
Here I leave the creation of the project step by step.
MATERIALS:
-Axes axial
-tranny axial
-dig 3r
-dampers 3r
-winch 3r, even without putting
-Tires (the original one proline badlands and the current one MoAbs)
-wheels DNS
-Junfac-cardan front (because the rear is the dig because it is shorter)
-Servo 15 kg
-4ch transmitter futaba check the trigger as a check for one friend. I have not yet so I can not post pictures, I have not seen and I haha
-Rc4wd tube chassis
-and well what I will leave now forgotten nurse in the process of creation jejeje.
PROBLEMS
-The first problem I found when opening the box with the material, and I was surprised to see a shaft with the support of the links above party, to fix I made these formats:
Support broken
new anchors:
Forward
Back
Once solved this issue, I began to assemble, to have it finished.
-My second mistake was riding patella long on one side than another, so that the rear axle was 1cm more separated from the chassis on one side than the other, solve it by putting them in equal measures, the truth is that was a mistake the most awkward.
FEATURES
-One of the main features is the suspension, that I have pretty limited so that the car becomes more stable, is in my semidroop, and although it has a lot of suspension, it makes up with its high stability, with the weight of the tubular me his own cost. This was a very difficult decision to make lol because I like cars with great suspension, but I think you and found a middle ground for me like this to pm, here you have some photos with maximum articulation:
Lateral Stability
Vertical stability
-In height, the car will land at rest 6.5cm and 10cm estiraza even in the second picture is with the wheels without tires as it touches the ground so no undir suspension and can be displayed better headroom:
Repose
high
-Another feature that is barely noticeable, is that the back is longer than up front, but just 0.5cm or 1cm, and is also somewhat higher in back than up front, but not much in the first picture appears much higher back because it has the rear wheel up pliers jeje:
Before
Now
-The dig is to put it microserve do not know if this will be able to move it, if you say see it or I will not put a great servo and see if someone over there has proven to me, because I pushed the arm microserve and this pretty hard, I don´t know to force the pots have these
He has new shoes
and little more, now I've put a new configuration of links, is this (with links inside the chassis):
and I can only part of the electronics that I hope to finish soon.
The entire thread you can see it here, but is in Spanish:
http://www.zonacrawling.com/foros/viewtopic.php?f=3&t=8024
I hope you enjoy
