wojin
Rock Crawler
can the rooster crawler handle a 27 turn and 7 cells? i know its a 27 turn limit, but is 8.6v too much. or should i go with a 35 turn?
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
novak rooster ???
- Thread starter wojin
- Start date
MasterShake44
Rock Crawler
Are you using the motor that comes with the stock AX-10 RTR? 27 turn seems kind of low for a crawler. But to answer your question it should be able to handle it, I know guys running lipos with their Rooster CE.
vipxj
RCC Addict
I run a rooster in my cr01 with standard 27 turn motor and 7 cell ,it goes fine,plenty of speed and torque!
MasterShake44
Rock Crawler
Cool, I thought that 27 turn would be too low. A friend of mine bought the AX-10 RTR and bought an 85 turn because he didn't like the 27. I'm sure it has something to do with your gearing too.
wojin
Rock Crawler
i planed on a smaller pinion and bigger spur, just want to know if the electronics will hold a 27 with 7 cells
i can change the throttle curve and aplication speed on my controler, so im sure i can get it controlable at crawl speeds. i just want some balls out power when i "need" it[do we ever really need it?(who am i kidding?)]
i can change the throttle curve and aplication speed on my controler, so im sure i can get it controlable at crawl speeds. i just want some balls out power when i "need" it[do we ever really need it?(who am i kidding?)]
Last edited:
xirtic
RCC Addict
The NOVAK crawler products are safe on either a 2 Cell (7.4v) lipo or a 7 Cell NiMH pack. Do not run more cells than recommended...or POOF. I was running 6 cells on my Novak Goat until last night....just made the switch to a 2 cell 20C 7.4v Lipo....it is NICE. I am sure that the Rooster in your brushed application will offer plenty on either setup. Novak does a great job on less cells. PLUS the strong BEC built into the ESC is great.
wojin
Rock Crawler
ive been running 7 cells since i got it. the question is more about a 27 turn with 7 cells. i think its a no-go though. got this off Novak's site
ROOSTER CRAWLER-EDITION SPECIFICATIONS
Forward/Reverse: Forward and Reverse
Input Voltage: 4-7 Ni-Cd/Ni-MH cells (1.2V/cell) or 2 Li-Poly cells
Footprint: 1.54" x 1.18" (39 x 30 mm)
Weight: 2.66 oz. (75.5 g) w/wires; 1.57 oz. (44.5 g) w/o wires
On-Resistance: 0.0014 ohms (forward); 0.0028 ohms (reverse)*
Rated Current: 400 amps* (forward)
Braking Current: 200 amps*
BEC: 6.0 volt/5.0 amp
Motor Limit 27-turn brushed (at 6 cells Ni-MH)
Discrete Steps: 256 Forward; 256 Reverse
Battery Plug: Tamiya
Drive Profiles: 2
Status LEDs: 2
Voltage Cut-off: 6.25 volts (Li-Poly Profiles)
ROOSTER CRAWLER-EDITION SPECIFICATIONS
Forward/Reverse: Forward and Reverse
Input Voltage: 4-7 Ni-Cd/Ni-MH cells (1.2V/cell) or 2 Li-Poly cells
Footprint: 1.54" x 1.18" (39 x 30 mm)
Weight: 2.66 oz. (75.5 g) w/wires; 1.57 oz. (44.5 g) w/o wires
On-Resistance: 0.0014 ohms (forward); 0.0028 ohms (reverse)*
Rated Current: 400 amps* (forward)
Braking Current: 200 amps*
BEC: 6.0 volt/5.0 amp
Motor Limit 27-turn brushed (at 6 cells Ni-MH)
Discrete Steps: 256 Forward; 256 Reverse
Battery Plug: Tamiya
Drive Profiles: 2
Status LEDs: 2
Voltage Cut-off: 6.25 volts (Li-Poly Profiles)
Similar threads
