pobrockcrawler
Rock Crawler
unless i've missed it, what about the tamiya hilux body?:???:
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
scx10 body guide
- Thread starter foproy
- Start date
Titus
Pebble Pounder
Tamiya Tundra fits honcho wheelbase 12.3". Its very close. 1mm out as i found out. this is refering to the bed and cab by the way.
Cheers
T
Cheers
T
foproy
Quarry Creeper
the hilux is a bit narrow, other than that i believe it fits the dingo wb the clod buster is a bit on the short side. these too if anyone can verify for me it would be appreciated.
ShawnCaudill
Newbie
Pro-Line 1972 Chevy C-10 Clear Body 3251-00
Didn't see this one listed. It fits nice one my Bruiser chassis (11.5" wb) 1.9" rims with RC4WD Mud Thrashers on K44 axles and narrowed chassis. You will need to trim up the bottom of the cab to front of the bed by about 3/8" to make it look right with the wheels and chassis (clearance and looks).
Nice Thread "thumbsup"
Didn't see this one listed. It fits nice one my Bruiser chassis (11.5" wb) 1.9" rims with RC4WD Mud Thrashers on K44 axles and narrowed chassis. You will need to trim up the bottom of the cab to front of the bed by about 3/8" to make it look right with the wheels and chassis (clearance and looks).
Nice Thread "thumbsup"
Solitaire
RCC Addict
HPI 7182 Wrangler - 12.3" WB
Plus it's 8.25" wide, so it's good for those that like widened axles.
Plus it's 8.25" wide, so it's good for those that like widened axles.
lonleycreeper
I wanna be Dave
Tamiya highlux 11.5"
Tamiya bronco 10"
Tamiya s blackfoot aka f150 9 3/4"
Tamiya clod 10.5"
Tamiya bronco 10"
Tamiya s blackfoot aka f150 9 3/4"
Tamiya clod 10.5"
Last edited:
foproy
Quarry Creeper
thank you its listed under the dingo bodies. i only put part numbers on bodies with multiple listings. like that proline wrangler.
i am ordering a bronco body from hpi soon and was going to add those assuming they are all the same wheelbase. they seemed to be right around 11.8 though.
this list is ment for bodies that are a close fit and dont require any mods to teh wheelbase. though i may edit in another section for close bodies.
foproy
Quarry Creeper
and again both blazers are listed on the first page. the cgr is a longer wheelbase. as far as the 350 goes, make your body then your links it is best not to assume anything. to many variables.
Last edited:
foproy
Quarry Creeper
actually the 11" blazer is a for the mini revo.
Creeping Ghost
Newbie
the body was out before the mini revo. its for 2.5 tmaxx,2.5 revo,
foproy
Quarry Creeper
added the priline f250. if anyone is wondering why i added it to the honcho list even though it is only the cab, honcho bodies built like that do not look right on a dingo wheelbase. the rear tires sit to close to the cab.
TennesseeCrawler
Newbie
No.. The 2dr Wrangler just says " for 1/10 scale crawlers "... The 4 dr JK Rubicon says for 12.3in. Wheelbase, a DIRECT fit for the honcho..The Cherokee is for 1/10 non-specifically too
TennesseeCrawler
Newbie
Btw nice list
dwblue00
Quarry Creeper
As a fyi the G6 rubicon has a in between wheelbase of the honcho/rubicon unlimited and the dingo. I think its somewhere around 12". Just thought I'd add to the confusion....lol!
I got two the Axial Classic Early 50's Gmc/Chevy Bodies that are 11.5 for short wheel base scx10 and a Proline International scout body that's 11.5 wheel base, and a Axial Ridgecrest body that's 12.5 wheel base
Last edited: