Some q's about trannys

[mudhunter]

can i hook 2 tranns to geather? bout like a t case? run the frount axles off one trans and the back off a 2ed tranny? and use a 4channle raido to contro them>

 

[BENDER]

If each axle has it's own tranny, then the 2 trannies aren't tied together. If you want one to be a T-case, then one tranny has to drive the 2nd tranny, which drives your axles. Either way can work.

 

[mudhunter]

i am running x factor axles and am usein 2 xxt trannys...
if i had one tranny per axle how would i contro them..i know i need 2 esc and 2 motros and i have a stock mgt tx and rx could i use that or do i need to get a diff rx and tx?

 

[Thorsteenster]

"Y" cord for the esc's, plug em both into one port on the rx

 

[S-Dog]

couldnt it just be wired like a clod?

 

[4link4eva]

It could, but then why not just get a clod? I think his aim is to control the front and rear axle speed independantly, so it would defeat the point.

 

[mudhunter]

Yea i want to be able to run like the frount axle by it's self like frount dig and all..
i just dont get the eltc part of this hold system..lol

 

[xjman]

If both trannys are locked I don't see why it wouldnt work.

You would probably have to run 1 ESC for each motor, plug each ESC into the respective port on your transmitter. I defentally see it working, but it does seem a bit over complicated.

 

[mudhunter]

i thought have onley frount stear..
have having the rear motro hooked like a regler motro usein the triger for f/r and usein the wheel for the frount steer..i just dont know how to hook the frount motro..I dont want a togle switch like one a moded tq3 i want it to be like the triger were i can put that mount of presher on it..i might end up hookin it up like a clod for now were i can run the truck and get all the shocks and ever thing set up.
thanks

 

[xjman]

I thought about only front steer..
Having the rear motor hooked like a regular motor using the triger for f/r and using the wheel for the front steer..i just dont know how to hook the frount motor up..I dont want a toggle switch like one a moded tq3 i want it to be like the triger were i can put that mount of presure on it..i might end up hookin it up like a clod for now were i can run the truck and get all the shocks and ever thing set up.
thanks

Ok, After busting out the decoder ring I fixed that.

If you use a stick transmitter you can control each motor seperately. One on the left stick, that will include steering for the front and throttle, and one for the right stick, that will control rear steer and throttle.

 

[toyofast]

Yea i want to be able to run like the frount axle by it's self like frount dig and all..
i just dont get the eltc part of this hold system..lol

I have a Clod with dig... it's easy to make dig happen on a dual motor rig and only one ESC.

 

[toyofast]

i thought have onley frount stear..
have having the rear motro hooked like a regler motro usein the triger for f/r and usein the wheel for the frount steer..i just dont know how to hook the frount motro..I dont want a togle switch like one a moded tq3 i want it to be like the triger were i can put that mount of presher on it..i might end up hookin it up like a clod for now were i can run the truck and get all the shocks and ever thing set up.
thanks

WTF did you just say?

 

[mudhunter]

Sorry about the spelling my mom was rushin me because i had to go to the doc..
what would be a good stick raido and reciver..