RCCrawler Forums

Richterat83 · 08-22-2014, 02:19 PM

oh loads. . . .

Here's the before pic of how it was

8 channel rx, light controller, brake light/reverse light/running light controller, BEC, and wiring harnesses in the rear box with winch controller in the front box.

I should have an updated pic later tonight after re-arranging

Johnnysplits · 08-23-2014, 07:37 AM

This is how mine has been since I built it...

Johnnysplits · 08-23-2014, 07:39 AM

This is the new brick I got to replace the two...

Johnnysplits · 08-23-2014, 07:41 AM

And this is where it's going...

Sailingeric · 08-23-2014, 04:08 PM

I went out and tested my new RC4WD Irok 1.9 tires on the comp course that I struggled with last weekend with my stock tires. These tires make a big difference and where my old tires just spun, these dug in and SCX10 acted like it was nothing.

lonleycreeper · 08-23-2014, 05:45 PM

Beat on her.

Jfrisch01 · 08-23-2014, 06:09 PM

Took the ol lady swimming

Berman · 08-23-2014, 10:12 PM

Weighted my front wheels, 220g in each, probably a bit excessive but it climbs like a champ!

Meekster · 08-24-2014, 04:09 PM

Upgraded my cr scx10 today

Sent from my iPad using Tapatalk

T I N Y · 08-24-2014, 06:14 PM

I made some brackets so I could mount two D ring shackles to the back of my G6.These are the mock up ones. I also made a new hook for my winch. I made it out of a finishing nail.

Johnnysplits · 08-24-2014, 06:19 PM

Got a set of titanium steering links on the way from Blue Monkey rc.

T I N Y · 08-24-2014, 07:31 PM

Quote:

Originally Posted by Johnnysplits

Got a set of titanium steering links on the way from Blue Monkey rc.

uppers and lowers?

pvo_srt4 · 08-24-2014, 09:47 PM

added axial light bar to my Jeep Rubicon Unlimited

also added the 2nd light bar to my G6

Gahndi · 08-24-2014, 09:54 PM

Installed vp stage 1 kit axial universals and mounted vp kmc enduros.

And Installed crawler innovations deuces wild closed cell foam for proline tsls xls

And also Added axial universal 5 bucket light bar and axial aluminum steering linkages I had laying around.

Johnnysplits · 08-25-2014, 03:24 AM

Quote:

Originally Posted by T I N Y

uppers and lowers?

Steering links for the high steer knuckles.

58513 · 08-25-2014, 03:40 AM

After my front wheels pointed towards each other a few times on my last crawl I made an aluminium link (just a bit of flat al. shaped up). My wheel alignment isn't that great (probably out by 3-5deg each side out wards but at least my wheels stay where I point them! Finished it off with a bit of heat shrink because the edges looked like crap lol. Also strung a bit of chain between the 2 D-shackles on my front bar. Just for giggles.

EDIT: You may also notice my sitcom LED system, or part of it. I disassembled an LED torch which gave me a switch, about 30 LEDs, a mad little LED light bar looking plastic frame and most importantly, a battery case, which Menes I can run the PEDs completely separate from the rigs main electronics!

Sent from my iPad using Tapatalk

ShrinerTony · 08-25-2014, 12:08 PM

Had to replace another Axial universal pin. 3rd one I've broken in about 6 months. Guess I found the weakest link

mudbeast2 · 08-25-2014, 12:13 PM

Those cv's suck! Mine broke as well. Do the XR mod you will not regret it.

Sent from my iPhone using Tapatalk

Richterat83 · 08-25-2014, 12:31 PM

Ordered a set of T-maxx driveshafts. Also put out a feeler thread for my HH motor and might go brushless on it.

Tmaxxed · 08-25-2014, 12:43 PM

Ordered up a hh br-xl waterproof, vanquish stage 1 kit, hitec waterproof servo, vanquish titainium drag link and tie rod, proline scaler shocks, extended hexes, and some 2.2 mudslinger xl's.

08-22-2014, 02:19 PM	#1061
Richterat83 RCC Addict Join Date: Jun 2013 Location: Port Saint Lucie, Florida Posts: 1,050	Re: What did you do to you SCX-10 today? oh loads. . . . Here's the before pic of how it was 8 channel rx, light controller, brake light/reverse light/running light controller, BEC, and wiring harnesses in the rear box with winch controller in the front box. I should have an updated pic later tonight after re-arranging Last edited by Richterat83; 08-22-2014 at 02:21 PM.

08-23-2014, 07:37 AM	#1062
Johnnysplits I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL. Posts: 2,545	Re: What did you do to you SCX-10 today? This is how mine has been since I built it...

08-23-2014, 07:39 AM	#1063
Johnnysplits I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL. Posts: 2,545	Re: What did you do to you SCX-10 today? This is the new brick I got to replace the two...

08-23-2014, 07:41 AM	#1064
Johnnysplits I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL. Posts: 2,545	Re: What did you do to you SCX-10 today? And this is where it's going...

08-23-2014, 04:08 PM	#1065
Sailingeric Rock Stacker Join Date: Jul 2014 Location: Hillsboro Posts: 70	Re: What did you do to you SCX-10 today? I went out and tested my new RC4WD Irok 1.9 tires on the comp course that I struggled with last weekend with my stock tires. These tires make a big difference and where my old tires just spun, these dug in and SCX10 acted like it was nothing.

08-23-2014, 05:45 PM	#1066
lonleycreeper I wanna be Dave Join Date: Oct 2010 Location: Caldwell ID. Posts: 4,328	Re: What did you do to you SCX-10 today? Beat on her.

08-23-2014, 06:09 PM	#1067
Jfrisch01 Quarry Creeper Join Date: Sep 2012 Location: St louis Posts: 346	Re: What did you do to you SCX-10 today? Took the ol lady swimming

08-23-2014, 10:12 PM	#1068
Berman Newbie Join Date: Jun 2013 Location: Hobbitland NZ Posts: 37	Re: What did you do to you SCX-10 today? Weighted my front wheels, 220g in each, probably a bit excessive but it climbs like a champ! Last edited by Berman; 08-23-2014 at 10:15 PM.

08-24-2014, 04:09 PM	#1069
Meekster Newbie Join Date: Dec 2013 Location: Calgary Posts: 5	Re: What did you do to you SCX-10 today? Upgraded my cr scx10 today Sent from my iPad using Tapatalk

08-24-2014, 06:14 PM	#1070
T I N Y RCC Addict Join Date: May 2008 Location: Southern,WV Posts: 1,136	Re: What did you do to you SCX-10 today? I made some brackets so I could mount two D ring shackles to the back of my G6.These are the mock up ones. I also made a new hook for my winch. I made it out of a finishing nail.

08-24-2014, 06:19 PM	#1071
Johnnysplits I wanna be Dave Join Date: Jan 2009 Location: New Port Richey, FL. Posts: 2,545	Re: What did you do to you SCX-10 today? Got a set of titanium steering links on the way from Blue Monkey rc.

08-24-2014, 09:47 PM	#1073
pvo_srt4 Quarry Creeper Join Date: Jul 2013 Location: Toronto Posts: 205	Re: What did you do to you SCX-10 today? added axial light bar to my Jeep Rubicon Unlimited also added the 2nd light bar to my G6

08-24-2014, 09:54 PM	#1074
Gahndi Newbie Join Date: Jul 2012 Location: Lafayette Posts: 36	Installed vp stage 1 kit axial universals and mounted vp kmc enduros. And Installed crawler innovations deuces wild closed cell foam for proline tsls xls And also Added axial universal 5 bucket light bar and axial aluminum steering linkages I had laying around. Last edited by THX_138; 09-05-2017 at 01:56 AM. Reason: All three posts on the same day

08-25-2014, 03:40 AM	#1076
58513 Newbie Join Date: Aug 2014 Location: QLD, Australia Posts: 24	What did you do to you SCX-10 today? After my front wheels pointed towards each other a few times on my last crawl I made an aluminium link (just a bit of flat al. shaped up). My wheel alignment isn't that great (probably out by 3-5deg each side out wards but at least my wheels stay where I point them! Finished it off with a bit of heat shrink because the edges looked like crap lol. Also strung a bit of chain between the 2 D-shackles on my front bar. Just for giggles. EDIT: You may also notice my sitcom LED system, or part of it. I disassembled an LED torch which gave me a switch, about 30 LEDs, a mad little LED light bar looking plastic frame and most importantly, a battery case, which Menes I can run the PEDs completely separate from the rigs main electronics! Sent from my iPad using Tapatalk Last edited by 58513; 08-25-2014 at 03:43 AM.

08-25-2014, 12:08 PM	#1077
ShrinerTony Rock Stacker Join Date: Sep 2013 Location: Orlando Posts: 52	Re: What did you do to you SCX-10 today? Had to replace another Axial universal pin. 3rd one I've broken in about 6 months. Guess I found the weakest link

Sponsored Links

What did you do to you SCX-10 today? - Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
scx cherokee and my f100 scalin today....	josh97	Axial SCX-10	2	08-28-2011 04:55 PM
Ogt my scx 10 tr today	scaleerdad	Axial SCX-10	2	10-15-2009 09:44 PM

08-25-2014, 12:13 PM	#1078
mudbeast2 Rock Crawler Join Date: Aug 2012 Location: Port St Lucie Posts: 538	Re: What did you do to you SCX-10 today? Those cv's suck! Mine broke as well. Do the XR mod you will not regret it. Sent from my iPhone using Tapatalk

08-25-2014, 12:31 PM	#1079
Richterat83 RCC Addict Join Date: Jun 2013 Location: Port Saint Lucie, Florida Posts: 1,050	Re: What did you do to you SCX-10 today? Ordered a set of T-maxx driveshafts. Also put out a feeler thread for my HH motor and might go brushless on it.

08-25-2014, 12:43 PM	#1080
Tmaxxed Rock Crawler Join Date: Aug 2010 Location: Esko Posts: 640	Re: What did you do to you SCX-10 today? Ordered up a hh br-xl waterproof, vanquish stage 1 kit, hitec waterproof servo, vanquish titainium drag link and tie rod, proline scaler shocks, extended hexes, and some 2.2 mudslinger xl's.

RCCrawler Forums

Thread: What did you do to you SCX-10 today?