|
| LinkBack | Thread Tools | Display Modes |
07-25-2012, 08:54 PM | #1 |
Rock Crawler Join Date: Jan 2012 Location: Hudsonville, MI
Posts: 875
| Robinson Racing 32p 56t slipper & .8 mod pinion?
I'm looking at getting the SuperShafty top shaft and the RRP 32p 56t Gen 3 slipper for my Wraith. I read that the RRP Gen 3 slipper needs a .8 mod pinion gear. Not finding a .8 mod pinion gear with a 1/8 bore. Can I use a my current RRP 32p (1/8 bore) pinion gears on the 56t 32p Gen 3 slipper? I'm currently running 32p gears now. Does matching the modules that big of deal? Thanks for your help! |
Sponsored Links | |
07-25-2012, 09:15 PM | #2 |
Rock Crawler Join Date: May 2012 Location: Washougal
Posts: 625
| Re: Robinson Racing 32p 56t slipper & .8 mod pinion?
There is only a slight differance. I was running 32p pinions before I knew any better and it seemed noisy. I went and got some .8mod, RR does make them, and it didnt seem to make any less noise. I think you are good to run 32p but others may know more.
|
07-26-2012, 03:35 AM | #3 |
Rock Crawler Join Date: Jan 2012 Location: Hudsonville, MI
Posts: 875
|
Yep, I'm currently running 32p spur and pinion now. I read that the RRP Gen 3 slipper requires .8 mod pinion gears. RRP makes .8 mod pinion gears, but for a 5mm shaft size. My HH motor has a 1/8" shaft size. Just wondering if my current 32p (which aren't .8 mod) pinions will work with the RRP Gen 3 slipper? Sent from my iPhone using Forum Runner |
07-26-2012, 05:21 AM | #4 |
Rock Crawler Join Date: Jan 2012 Location: Hudsonville, MI
Posts: 875
|
Ok!!! Did some more research on this. 32 pitch and .8 mod are essentially the same. .8 mod is actually 31.7 something pitch. So, as long as I run a 32 pitch pinion obviously, and the 32 pitch RRP Gen 3 slipper, it will work. Sent from my iPhone using Forum Runner |
07-26-2012, 08:20 AM | #5 |
RCC Addict Join Date: Dec 2011 Location: Raleign
Posts: 1,439
| Re: Robinson Racing 32p 56t slipper & .8 mod pinion?
I'm running same sized spur with 12t Traxxas pinion which is .8mod and it's been running fine for a while. It's pretty noisy, but is looking good.
|
07-26-2012, 09:28 AM | #6 |
RCC Addict Join Date: Feb 2008 Location: Tekin, ID
Posts: 1,940
| Re: Robinson Racing 32p 56t slipper & .8 mod pinion?
Run it a little on the loose side too since they aren't exactly the same. I always find that running it more loose than I normally do with 48p seems to quiet it down too.
|
07-26-2012, 10:59 AM | #7 |
Rock Crawler Join Date: Jan 2012 Location: Hudsonville, MI
Posts: 875
|
I guess I could get the 5mm to 1/8" spacer for my motor shaft. Then I would have no problems with finding 32p .8 mod pinion gears. HARLEY!!! Need your input on this!!! Thanks for the info guys! Sent from my iPhone using Forum Runner |
Robinson Racing 32p 56t slipper & .8 mod pinion? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Robinson slipper 56T Gen3 Slash | sixhundred71 | Axial Wraith | 2 | 03-25-2015 07:38 AM |
Converting To a Robinson Racing Slipper Clutch | tractionaction | Axial SCX-10 | 0 | 06-15-2012 03:56 AM |
robinson racing slipper 48p | kmas | Axial Wraith | 3 | 05-11-2012 10:08 PM |
Robinson Racing Wraith Slipper unit & gears IN STOCK | RPP Hobby | RPP Hobby | 0 | 01-13-2012 09:27 PM |
| |