Re: IFS kit for Wraith
 

Everythings here and It's started
Couple of Questions :
Am i correct in saying it needs a way short servo horn ? Milled one down just now
Will the stock wraith upper link mount have to be shaved off ?
What's everyone using for hingepins ?
Cheers
Jack

Re: IFS kit for Wraith
 

it depends on your driveshaft. i'm running the MIP shaft up front so my horn tip was super close and i shaved it down very slightly to be safe. i'm using the second hole. stock driveshaft should fit fine.

negative

Re: IFS kit for Wraith
 

Really STOKED with how this kit runs and crawls!

<object height="480" width="640">


<embed src="//www.youtube.com/v/g5wP2KQ0Pu4?version=3&hl=en_US&rel=0" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" height="480" width="640"></object>

Re: IFS kit for Wraith
 

I'm on wraith Mip's , axial horn and 6mm supershafty outputs .
All sorted now cheers , She'll be running tomorrow .
Kit went together very well cheers :)
Jack.

Re: IFS kit for Wraith
 

sick.

Re: IFS kit for Wraith
 

:twisted:
down with the sickness

Re: IFS kit for Wraith
 

Thanks Guys. I posted a longer one today.

<object height="480" width="640">


<embed src="//www.youtube.com/v/S-4biebib0k?hl=en_US&version=3&rel=0" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" height="480" width="640"></object>

So now you don't have to mod to make a wrexo haha

Sent from my SGH-M919 using Tapatalk now Free

Re: IFS kit for Wraith
 

killer vid. thanks

Re: IFS kit for Wraith
 

I was placing everything together with all the same parts you stated (same set up with MIP and vanquish ) when I go to mate the slash stubs into the vanquish hub the bearing outboard closest to the tire sticks out several mm. How can I fix this with shimming the inside of the hub?

I haven't cleared any room out for the mip bell yet without knowing.

thanks,
-Aaron

Re: IFS kit for Wraith
 

Well it took me long enough to finish this build but it is finally done. IFS and twin shock trailing arms and a 3600kv short course motor on 3s powering it.

http://i1291.photobucket.com/albums/...ps35a64c4a.jpg

http://i1291.photobucket.com/albums/...psd99f0267.jpg

http://i1291.photobucket.com/albums/...ps6a2b4962.jpg


And of course, a series of pictures wouldn't be complete without...

http://i1291.photobucket.com/albums/...ps2a269ca6.jpg


After getting all the shocks tuned in and ride heights set, it now jumps like a champion and flys like an arrow. You sir, are a magician.

Re: IFS kit for Wraith
 

working on getting my kit together got some parts coming and workin on the body

Attachment 258924

Re: IFS kit for Wraith
 

http://i15.photobucket.com/albums/a3...ps4541347a.jpg

A little bit of powder coating never hurt anything.

Still trying to figure out the hubs with MIP shafts though.

Re: IFS kit for Wraith
 

WHAT BODY IS THAT!!!! It looks awesome mate. "thumbsup"

Re: IFS kit for Wraith
 

it started out as this hard body off some random cheapo rc car"thumbsup"
Attachment 258972

Re: IFS kit for Wraith
 

Hey blue monkey i have a question, did i do something wrong my steering is hitting the side of the lower chassis and the steering cross piece is like a 1/16" away from hittint the output on the diff, no room for a driveline or a drive cup, Any HELP would be awesome!!! Thanks Hopefully im just a retard and did somethin wrong i havent taken it back apart to check it out yet

Attachment 258998

Attachment 258999

Re: IFS kit for Wraith
 

the traxxas bellcrank is adjustable so you can gain clearance from the plate if needed and apparently the traxxas unit is not as close to the diff input either.

yours looks good but unfortunately you need the adjustability of the traxxas bellcrank. the only other option is if you want me to run some custom plates thru the process that will work with that bellcrank.

Re: IFS kit for Wraith
 

FYI we're making a MIP/locker conversion kit for the EXO diff based on a suggestion and specs provided by frdtrkguy. totally bolt-on. we do all the machine work and provide all the hardware. i'm just waiting on a batch of parts from MIP to complete the first few sets for testing.





we're also extremely close to having a working prototype of the SCX10 IFS using the ultra-common traxxas IFS. we chose the traxxas because its width matches the scx10.

Re: IFS kit for Wraith
 

Awesome news. If you need a tester/hot off the press/pre-order buyer, I'm your huckleberry!

Re: IFS kit for Wraith
 

Thanks BMRC, the locker is no problem. I am attempting to figure out how these fellas are fitting everything (my bearing hangs out about 2mm) inside the vanquish exo knuckles.

Your IFS kit is on point! "thumbsup"