|
| LinkBack | Thread Tools | Display Modes |
02-20-2013, 08:44 PM | #1 |
Quarry Creeper Join Date: Nov 2012 Location: oshkosh
Posts: 206
| Anyone use dielectric grease?
Do any of u guys use this stuff in battery connections or even for servo extendeders where the connection is in the open. Will it restrict the power from battery
|
Sponsored Links | |
02-20-2013, 11:48 PM | #2 |
Quarry Creeper Join Date: Apr 2012 Location: Lansford
Posts: 432
| Re: Anyone use dielectric grease?
Why put it on battery connectors? I would not worry about them corroding at all. Dielectric grease will not hurt electronics, but it is not conductive either. If you put this in connectors they may not contact very well, they will be slippery and messy, and they will collect dirt. Probably won't actually do anything as it may just push out of the way but it is not needed anyways. Dielectric grease would be acceptable on something such as packing inside your servo case so water doesn't get in there. I wouldn't even use it inside the ESC case as there are better more permanant alternatives such as plasti-dip or epoxy. For stuff like servo extensions if your that worried about them just cut the connectors and solder/heat shrink the wires together, or leave them as is. Even running in water and snow for a couple years I have not seen any negative effects on any of my connectors. If your in a salty environment consider soldering as much as possible, and if your battery connectors do corrode it will take some time and replacing them would not be a big deal to do every few years.
|
02-21-2013, 10:56 AM | #3 |
Quarry Creeper Join Date: Jun 2012 Location: Earth mostly
Posts: 478
| Re: Anyone use dielectric grease?
I used it in my bullet connectors from my motor to ESC and then shrink wrapped the outside because I was getting a lot if water in them. Has worked fine so far.
|
02-21-2013, 10:56 AM | #4 | |
Quarry Creeper Join Date: Nov 2012 Location: oshkosh
Posts: 206
| Quote:
| |
02-21-2013, 11:13 AM | #5 |
RCC Addict Join Date: Feb 2010 Location: a house
Posts: 1,986
| Re: Anyone use dielectric grease?
i use it on all my servos and all my deans connectors . keeps the water out of the deans and its not a slippery mess nor does it cut down on electrical flow or collect dirt. been doing it this way for 2 years, infact it lets the deans connect easier, just dont over do it on the grease. stay away from plasti dip , that crap IS a mess to work with there are better products to use
Last edited by crawlhog; 02-21-2013 at 11:16 AM. |
02-21-2013, 11:51 AM | #6 |
Quarry Creeper Join Date: Mar 2011 Location: over there...
Posts: 336
| Re: Anyone use dielectric grease?
My 1st water proofing I used dielectric grease on everything .receiver, esc, servo, if its electronic it works .still holding up just fine .. Took everything apart and loaded and coated all with it ..put cases back on .. Keeps stock clean look .. Im still trying to find a reason not to use it.. corrosion x or epoxy would be my 2nd choice but dielectric grease is cheaper and eazy to find local Last edited by bronc4now; 02-21-2013 at 11:55 AM. |
02-21-2013, 01:58 PM | #7 |
Quarry Creeper Join Date: Nov 2012 Location: oshkosh
Posts: 206
|
Thanks guys now r u guys putting the grease in the gear section of the servo or where the motor and circuit board is
|
02-21-2013, 02:53 PM | #8 |
Moderator Join Date: Jan 2004 Location: chicago
Posts: 2,814
| Re: Anyone use dielectric grease?
i have a friend who uses dielectric grease on his hitecs, and in the instance that the servo takes a dive and needs to be repaired, he simply cleans off the grease with motor spray and sends it into hitec. so thats a bonus. i used to use it all the time before i switched to conformal coating. |
02-21-2013, 04:52 PM | #9 |
RCC Addict Join Date: Feb 2010 Location: a house
Posts: 1,986
| Re: Anyone use dielectric grease? |
02-21-2013, 07:18 PM | #10 |
Quarry Creeper Join Date: Nov 2012 Location: oshkosh
Posts: 206
| |
02-22-2013, 10:08 AM | #11 |
Quarry Creeper Join Date: Apr 2009 Location: Ottawa, ON, Canada
Posts: 251
| Re: Anyone use dielectric grease?
It won't cause any loss of connection, the mechanical forces between the connectors will but through the grease just fine. It could collect dirt and it is possible that this dirt would prevent a good connection, but a quick cleaning would take care of it. I haven't used it for the battery but it's great on brushless sensored connectors. I put some on all my engine electrical connections on my 1:1 Jeep 15 years ago and never had a problem running the engine in water or pressure washing it, it's great stuff. I also use it on my trailers and block heater connections. |
02-22-2013, 06:32 PM | #12 |
Newbie Join Date: Feb 2013 Location: Westport, MA
Posts: 38
| Re: Anyone use dielectric grease?
I am an electronics technician. I use it on everything that is permanent or semi-permanent. It works great for electrical connections but I wouldn't use it on a battery connection that has to be disconnected all the time.
|
02-22-2013, 07:52 PM | #13 |
Quarry Creeper Join Date: Nov 2012 Location: oshkosh
Posts: 206
| It would only be for winter runs cuz of the salt until I can get a small air compressor dont have a good way to dry them off
|
04-03-2013, 09:48 AM | #14 |
Newbie Join Date: Feb 2013 Location: Kenova
Posts: 7
| Re: Anyone use dielectric grease?
I also have used it on my sensor leads and servo connections w great luck.
|
Anyone use dielectric grease? - Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
dielectric grease for waterproofing.. | m1009cucv | Electronics | 25 | 04-12-2013 12:18 AM |
Dielectric Grease??? | Evergreen CJ5 | Tools, and Procedures | 8 | 11-07-2011 04:56 PM |
dielectric grease question.... | discgolferlee | Electronics | 12 | 01-26-2011 02:29 PM |
Dielectric grease..... | Krawlin | General Crawlers | 2 | 07-24-2007 10:33 PM |
| |