| |
07-17-2012, 07:26 AM
| #1 |
| I wanna be Dave Join Date: Oct 2004 Location: QC-AZ
Posts: 2,352
|  Motor Clocking Jigs
I have posted pictures of these before but have never offered them for sale. I recently made some for a buddy and just had the laser shop finish off the material I had. Basically there are 4 jigs, one for each tooth pinion 12-15. They move the motor parallel to the servo so the clearance between the two remains the same regardless. Bolt them up, center punch the holes, scribe a few lines and get to cutting. It couldn't be easier. If there is interest PM me, if not I'll recycle them.   Last edited by rob_b; 07-17-2012 at 08:22 AM. |
|  |
| Sponsored Links | |
| | |
|
07-17-2012, 07:40 AM
| #2 |
| Rock Crawler Join Date: Jun 2010 Location: SENECA
Posts: 811
|  Re: Motor Clocking Jigs
Where do I send the money? Great idea  |
|
| |
|
07-17-2012, 07:41 AM
| #3 |
| I wanna be Dave  Join Date: Jan 2004 Location: Detroit
Posts: 3,583
| Re: Motor Clocking Jigs
I'll take a set of 13/14/15 right now! Paypal ready! YGPM
Last edited by binaryterror; 07-17-2012 at 07:44 AM. |
|
| |
|
07-17-2012, 07:46 AM
| #4 |
| Pebble Pounder  Join Date: Apr 2011 Location: El Paso
Posts: 191
| Re: Motor Clocking Jigs
That's a cool idea if I had those when I went 86jeep it would have made it a lot easier
|
|
| |
|
07-17-2012, 07:52 AM
| #5 |
| I wanna be Dave Join Date: Oct 2008 Location: Sumter
Posts: 6,141
| Re: Motor Clocking Jigs
I'll take a set of all three as well...GREAT IDEA!!!!
Last edited by ittybitty; 07-17-2012 at 07:57 AM. |
|
| |
|
07-17-2012, 07:54 AM
| #6 | |||
| I wanna be Dave Join Date: Oct 2004 Location: QC-AZ
Posts: 2,352
| Re: Motor Clocking Jigs Quote:
Quote:
Quote:
| |||
|
| |
|
07-17-2012, 09:52 AM
| #7 |
| Rock Crawler  Join Date: Dec 2008 Location: Displacement
Posts: 525
| Re: Motor Clocking Jigs
Those are sweet. Beats the hell out of a paper template.
|
|
| |
|
07-17-2012, 10:53 AM
| #8 |
| Rock Crawler Join Date: Nov 2008 Location: The Lone Star State
Posts: 722
| Re: Motor Clocking Jigs
Me like, great idea!
|
|
| |
|
07-17-2012, 11:30 AM
| #9 |
| I wanna be Dave Join Date: Oct 2004 Location: QC-AZ
Posts: 2,352
| Re: Motor Clocking Jigs
They are all gone. Guess they were a good idea after all. LOL
|
|
| |
|
07-17-2012, 12:09 PM
| #10 | |
| I wanna be Dave Join Date: Oct 2008 Location: Sumter
Posts: 6,141
| Re: Motor Clocking Jigs Quote:
| |
|
| |
|
07-17-2012, 12:12 PM
| #11 |
| I wanna be Dave Join Date: Oct 2004 Location: QC-AZ
Posts: 2,352
| Re: Motor Clocking Jigs
Yep, you got to be quick and sometimes a little lucky around these here parts.
|
|
| |
|
07-18-2012, 11:19 PM
| #12 |
| Quarry Creeper Join Date: May 2011 Location: El Paso TX
Posts: 240
| Re: Motor Clocking Jigs
make some more
|
|
| |
|
07-19-2012, 09:53 AM
| #13 |
| I wanna be Dave Join Date: Oct 2008 Location: Sumter
Posts: 6,141
| Re: Motor Clocking Jigs
Received mine today...thanks Rob!
|
|
| |
|
07-19-2012, 09:57 AM
| #14 |
| I wanna be Dave Join Date: Jan 2004 Location: Detroit
Posts: 3,583
| Re: Motor Clocking Jigs
Yup, got mine too today, can't wait to use them this weekend to get the front to fit a 15T or so.
|
|
| |
|
07-19-2012, 10:09 AM
| #15 |
| I wanna be Dave Join Date: Oct 2004 Location: QC-AZ
Posts: 2,352
| Re: Motor Clocking Jigs
Good to hear guys. I had to crank up the turbo to 11 to get to the PO before shipping deadline... made it 3 minutes early... guess 10 would have done  |
|
| |
 |
Motor Clocking Jigs - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| HELP! flipping/clocking motor mount... | dybbob | RC4WD Trail Finder 2 | 15 | 07-13-2012 06:09 PM |
| Motor Clocking??? | illz302 | HPI Wheely King | 2 | 08-02-2009 02:54 PM |
| Clocking of Tekin RS Motor in a LOSI?!?!? | kerrywittig | Electronics | 10 | 06-30-2009 09:48 PM |
| clocking a motor in a WK tranny and gearing ?? | 72Blazer | General Crawlers | 4 | 03-26-2007 12:16 AM |
| |
Linear Mode
