Super 1/8 Buggy Crawler, 4ws, 2wd,DIG,4wd 6watt mp3 Stereo 3 Attachment(s) April 2011 Update: Custom Rock Rings, LINK pg 12 Dec update page 11-12, BTA front steering, shortened WB to 16" Nov 2010 Update, Page 11 NEW PROLINE Super Swamper TSL 2.2 Tires on DE Racing Short course wheels. Narrowed Axles to 11.5 track June 2009 Update Crawler practically finished, Pics on PAGE 8 , Video of Engine sound and more on Page 9 Scale Super at Pacific Grove CA. VIDEO Crawling and broke Spur gear at Fordyce trail CA In dash MP3 PLayer PROJECT FULL THROTTLE SCALE SUPER Comp Buggy Custom Super Rock Buggy 1 seater with MP3 player and 6 Watt Stereo, rock lights, DIG ! :-P This build uses drivetrain from Axial tranny ,Revo drive shafts to Losi 8 Aftershock diff to Losi Hyper 8 shafts to XTM Mad force steering knuckles, , The build Begins ! 6ch Mini scale Super Rock buggy Crawler: Something for the trails when I'm not Crawling in my Scale Toyota :-P ( in other words when others are broke :roll: :lol: Big thanks "thumbsup" to : RCcrawler You guys ! for tech mods and feedback Yotachump- Chromoly Axial tranny outputs Robinson racing ax10 internal gears RCP -Beadlocks RPP - ESC MambaMax Holmes Hobbies, CC BEC FinishLine RC _Delrin Links TCS Crawler store , Motor BM16 Brushless BowTie-- for scale stickers Tower Hobbies, Wild Willy Driver, stickers, RC /Unlimited (LHS) for helping me find axle shafts that fit together Ebay for DX6 & non crawler hard to find parts Like the V8 Corvette Die cast motor I will try to Stuff under the Hood :shock: Think I bought something from Unimoger..? Hardware Suplliers: Olander- for Metric Hex head screws 3mm MMS - Standard Small Hex head bolts, 8-32 MSC for the Rod ends--NOT using. CHANGE to Losi 1/8 buggy rod ends with HPI 6.8 steel Balls Slinky Sam-- 1/4 D.O.M Tubing for Chassis McCaster- for 3/16 steel tube, Chassis- 1/4 DOM Tube rock buggy frame.- similar to SNIPER Picture below 4 link Suspension 7/16 Delrin lower 3/8 Delrin upper links Shocks Max Big bores. Switched to HPI Hellfire in 2010. Page 12, More travel Team Losi Aftershock Diffs. scratch built steel locker, Axles - scratch built 5/8 Stainless Angled Solid Axles & knuckles . 12" wide wheel width 14.2" axle build in progress April 1st :-P Axle shafts- 1/8 Losi truggy Hyper 8. 5" shafts Knuckles - XTM Drive shafts- modified Revo . and Cen nemesis shaft for DIG Tranny- Axial with Robison Aluminum gears and Chromoly main output from Yotachump. 32pitch Kimbrough-66/14= 55.2:1 Motor- 55 Turn->overheats, Now Using BM16 Brushless 1000kv ESC - MAMBA MAX. Battery- Dec 2008-Upgrading to 3S lipo 2250 30c. The Old batt. in pics is Cheap battery packs.com , custom split 4 pack 8 cell 4500. Lasts 1.1 hours "thumbsup" With 5 servos & lights, Radio - 6 Channel Spectrum DX6, ebay "thumbsup" Later switched to a DX6I and then Modded into a Pistol Grip-> See signature below for Link Servos: HITEC 7955tg Ch#1 ESC Ch#2 Front Steering - 5955 . Ch#3 Rear steer - 7995 or Mini Actuator Ch#4 Rear DIG HS 225 servo-> sucks not strong enough. Going to Mini actuator Ch#5 Lights =10mm and SDM LED's not yet installed [/COLOR] ROD ENDS Losi buggy with HPi 6.8 heat treated steel balls 18" wheel base 14" wide. Weight- loaded 11 lbs Tires- Proline Moab XL's . In 2010 Page 12 I Switched to Proline TSL SX 2.2 tire on Shortcourse DE Racing wheels Rims- Axial 40 series Narrowed to 2 1/8 Beadlocks -scale Hex bolts Custom machined Rock Rings Not yet installed . Foam, custom cut with rolling ground weight Scale Features - ROCk Lights: Super 100,000 mcd 10mm LED's X7, two headlights, one rear, 4 under chassis Rock lights 1/10 scale Recaro seat SONY MP3 Stereo with Altec Lansing portable sound unit. 6 watts PICTURES BELOW: 1- New Axle assembly, Team losi aftershock Diff 2- Steel Locker 3- 8 cell split battery, Elite 4500. Drive time 1.5 hour ! "thumbsup" Switched to 3S 2250 Lipo 4 Narrowed Axial with beadlocks & Moab XL Last pic top view of frame Crawler Buggy STATS Ratio 6.79:1 Total 58.35:1 motor speed 10955 RPM max speed 4 MPH KV 987 motor Torque .48 Axle Torque 27.9 ft-lbs motor Power 743.7 watts 1 Horse Power Thunder Power 3s Lipo 2250 Aprox Weight 10 lbs http://i588.photobucket.com/albums/s...t/CW040223.jpg |
lookin good so far, those axles are going to be hot.. cant wait to see the final build. |
Very unique idea on using the Losi Aftershock diffs!! It looks great so far!! Keep up the great work!!"thumbsup" |
looks like its gonna be sick, got a ? tho, wats the hydro. suspension? and adjustable height servo?? just some fancy words to say that you'll be able to lift and lowerl the truck at a touch of a button??:lol: |
2 Attachment(s) Quote:
Can't wait to have a tube buggy Yep ! you got it. it will help with steep hill climbs and the COG Finished mocking up and Spot welding the rear axle yesterday :-P Interesting part of attaching the axles to the Diff in a Clean scale manner, hmmm rear axle 0* caster |
thats gonna be sweet, them axles are beeef! and they look killer too. what kind of design you gunna go with on the tube frame.? |
1 Attachment(s) Quote:
I like Detail & unique so I'll find something then tweak it a bit here's a few I like, Sniper & well I'm really just liking Sniper, but if I were to build a 2.2 then it would be like the new single seat competition crawlers http://www.avalancheengineering.com/design.html http://www.avalancheengineering.com/sniperchassis2.htm |
Interesting idea on the Wheel weight. I'd like to hear an update after you get to run this thing. It's looken really good so far. |
Like the axle build....those will look great. Keep the pics coming. Jay |
the R2 s speed is shifted by a servo? i thought it was automatic...... |
Wow this is a pretty killer build. I love those axles. |
Killer axel set up. I thought of going with SS but was worried of the weight. Looks good ! |
Quote:
I think aluminum is to soft. Keeping the weight at axle height and lower will give you great COG results Thanks for the axle props, I may have rushed the build on these though I was building them thinking I would just attached them with plates like all the other emaxx tube axles guys do. But I want something "Cleaner" than that. So back to design board, Question? : What do you guys think about attaching the Large 1" short tube to the Diff with Brazing or JB weld and then Insert the 2nd tube ring inside and fastening toghether with 3 small short button head screws ? so that the axle are removable. I cannot remove axle shafts from the outside ends because the dogbone end pin is slightly to large. I doubt the OFNA Jammin universals will break so I could Braze or JB weld the whole axle together ? Idea Drawing is with screws Left First Tube is 1" with smaller middle tube snug fit inside 1st tube Diff housing is ALUMINUM Tubes are steel Now that I think about it, I cannot Braze Aluminum with Steel. I would need to use a Metal bonder like JB weld for this joint |
I was looking at the second picture say to myself that looks familiar then it click it was my axle picture. I still have a lot to do to mine. I sracpped the tubber chassis in favor of a stick like chassis. |
Quote:
I have yet to see a real stick chassis on a max driveline Very cool though |
Build update: Wheel Locks RC4Wd has a disconnect tranny to disconnect rear driveline so you can steer tighter. but right now it's only single speed, if they come out with a 2 speed version then I'll use it and add a Line lock for the rear brakes. If Not, then PLan B: Adding a driveshaft Brake for the Rear Driveshaft. and use the mechanics like the gas powered rc's use for brakes, like an old RC10Gt Thanks to the Maxx sticky thread http://www.rccrawler.com/forum/general-crawlers/5371-ive-seen-lots-posts-asking-about-revo-shafts.html I'll be using 5457 yoke for the rotor brake and the 5453 for the 5mm tranny shaft and the 5458 for the 8mm Losi Pinion shaft Humm... I ran out of radio channels LOL:lol: Servos: Ch#1 Throttle Ch#2 Front Steering - 5955 servo . Ch#3 Rear steer - either a 5955 or a 5995 Ch#4 Suspension- adjustable height servo 5955 Ch#5 Front Dig/ rear shaft lock, servo #? Ch#6 Tranny shift servo. stock servo |
1 Attachment(s) UPDATE: Well this build will be much slower than I had hoped. My spending is out of hand, The last 4 months I have SPENT $3400.oo in RC Hobbies, My Toyota crawler, 2nd 4runner , and Tooling. But the plans on the axles are almost finalized. Build progress change: Change in Design on front axles Braze Aluminum sleeve on Diff cover and use bolts to connect stainless axle housing also this wheel width is looking like 16" + so I'm most likely going to use OFNA Hyper 8 Axle shafts that are only 5" long each wheel width should be around 14" Wheel base around 16.5 or 17" Another Mod: 6 LED Rock Lights , 2 flood offroad front lights & 1 interior light, :idea: New Parts: RC4WD 2 Speed tranny & Revo shafts for drive shafts 1/10 scale recaro seats |
damn, those axles look killer. |
1 Attachment(s) Lookig into Rod ends Thanks to : Originally Posted by peej410 http://www.rccrawler.com/forum/image...s/viewpost.gif http://www1.mscdirect.com/CGI/NNSRIT...49458&PMT4NO=0 These are looking pretty cool 10/32 thread @ $2.86 |
them rod ends are ridiculous!! |
4 Attachment(s) Update: NEW PARTS DX6 Radio RC4WD 2 speed tranny but I don't like that the shift rod has no flat spot or hole to help connect a shift link to for the servo. ( emailed RC4WD, But no reply yet :roll: ) But it is spring loaded so it's stays in one gear until it is pushed inward. REVo shafts ebay, 4 @$25. Found my 3/4" Speakers so I can have TOONS when Crawling 8) I'll plug these into my IPOD shuffle under the hood . It may be awhile for this build, we just bought a house :-P and so have to Pack up , move in July-Aug and set up my new Garage :-P Here's some pics |
Wow thats going to be sick |
3 Attachment(s) So here's the 5" hyper 8 Shafts This puts the Outside wheel stance at 14.5" Center of wheels at 12.5 Is this to narrow, What do you think ?:?: |
looking good. |
14.5 would be just about right;-) "thumbsup" |
Not that I am really interested in Maxx crawlers, but this build is pretty sweet so far! I love all the custom touches everywhere. |
2 Attachment(s) Quote:
although it's not really a maxx, guess I could have stuck it in a different thread ? the only traxxas parts used are the revo drive shafts. Found me some Rock lights and head lights :-P after searching electronic stores with no success I went to ebay and spent $24. on a pack of 20 Blue LED's and and $20. on a pack of 50 White (non wired). I have lots of these for sale |
dangit! i wanted to be the first to put a radio in an rc! i got some headphones at the dollor store and used a little speaker out of a computer speaker. build is looking good! |
hows this thing coming along? |
Quote:
I hope to run a shaft from tranny input to the front where the Engine is in real life and mount the motor in front, Start on Frame next ! We just bought our first house and just moved in last week, Remodel still not Finished . Waiting on new garage door Too ! Garage is full of box's and house parts , it's chios ! It will be slow going Because I have a Modified Twin Stick to start mass Producing and get it out to all the guys waiting on it |
I <3 It |
Quote:
|
Quote:
|
Can you give us some info on the speakers? How are you going to wire them into a headphone jack? And where did you get them? |
1 Attachment(s) Quote:
Speakers from an old friend, no idea where they came from. But they have those Rc rappin trucks at Toy r us with the big wheels and radio, so you could part it out. If they Do not sound good then I'll buy Ipod portable speakers :) |
2 Attachment(s) Just bought These Bad boy Rod Ends "thumbsup" Steel for the lowers and the light thermoplastic for the uppers MSC http://www1.mscdirect.com/CGI/NNSRIT...49458&PMT4NO=0 and will have some by tomarrow others by monday I'll post my feedback when I get them 3/16 10/32 thread is 3/4 long outside diameter 5/8 1" 9/16 total long steel Rod End zink plated $4.36 static load 1200 the black one is thermoplastic self aligning $2.86 static load capacity 225 These will most likely not break if it takes a tumble 8) Now I just need to finalize on some strong links, any suggestions?? maybe 3/8 delrin for the uppers PS I have lots of the SUPER Bright LEDS if you need some |
2 Attachment(s) NEXT DAY Delivery!! and will get the rest today These are impressive !! :shock:"thumbsup":-P I will do the same for my steering links Sneak picture :lol: I happend to have a 3/8 Delrin link handy, size is good, but this Delrin seems to flex, so I have some testing to do 2nd Pic is comparison to my current max 1/4 links and stock rod ends |
Those are huge! |
Need some help here the Site MSC where I bought the thermo plastic rod ends does not identify them as LEFT thread, so I need a left thread hex nut. :?:Any sources where I can find a 10/32 left thread nut :?: already tried Mc Caster, Olander and MSC thanks |
2 Attachment(s) Found them ! $.47 each Awesome site for small Hex head bolts M4 , 6-32, 4-40 , 6-32 , 8-32 ,10-24 It's like Christmas :-P |
All times are GMT -6. The time now is 12:35 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com