Go Back   RCCrawler Forums > RCCrawler Brand Specific Tech > Tamiya Txt-1 and Juggernaut
Loading

Notices

Thread: RC4WD Extreme Duty XVDS for Clodbuster and TXT review

Reply
 
LinkBack Thread Tools Display Modes
Old 06-13-2014, 01:33 PM   #1
Rock Crawler
 
Join Date: Apr 2007
Location: Hawaii
Posts: 708
Default RC4WD Extreme Duty XVDS for Clodbuster and TXT review

Here's a quick installation review of the RC4WD Extreme Duty XVD for the Clodbuster.

Just some quick notes about my experience:

-CV joint action is pretty smooth. My TTR CVDs are smoother but that may be because they are broken in.
-parts are not directly interchangeable between the TTR version, that includes the hexes. This important as the RC4WD kit includes 14mm hexes and not 12mm hexes.
-loctite the set screws for the CV pins, they are loose from the factory.
-I needed to use the thinner 3.5mm bearings(as used on the TTR CVDs) instead of the included 4mm wide bearings for the inside of the knuckles.
-check to make sure the bearings will slide onto the outer shafts. Mine had issues and i had to grind one shaft a little.
-when installed correctly, the XVDs feel solid, no unnecessary slop.

Here's the XVD set as I received it, mostly assembled, with outer bearings, 14mm hex assemblies(hexes. pins. o-ring retainers), and two different length wheel bolts.



Comparison with the ThunderTech/MIP shafts:

The TTR shaft is on top, the RC4WD on the bottom. The shafts are the same length but due to the difference with the hex design the RC4WD shafts setup up just a hair wider. There is more angle on the RC4WD version but the CV action gets notchy at extreme angles. In practical application you would have to do serious modifications to take advantage of the extra throw. In the Clod and TXT axles I installed them in, with the "normal" steering mods for racing, they both provided the same amount of throw.



The "long" side inner shaft on the RC4WD version has the joint pin molded into it, unlike the TTR shaft which has a separate pin. What this means is there is a specific long shaft and a different short shaft whereas the shafts on the TTR version are interchangeable left or right.



Both use 8mm thick outer shafts. The pins for the CV joints is thicker on the RC4WD version. There's more taper on the RC4WD outer shafts to achieve the greater angles. How that plays out as far as durability remains to be seen, but the shaft is still thick in that area.



The RC4WD hexes use a larger drive pin so they are not interchangeable with TTR shafts unless you drill the TTR shafts out. The hex portion also carries all the way to the edge of the outer shaft so the width, from hex to hex, is slightly wider than the TTRs.



Installation: TXT axle

I first installed the set into a TXT axle and ran into a few problems. First off, the outer bearings were a pain to get on. I was able to get one side on with some tapping, but the other side required some grinding. Oddly when I was tapping the bearings on the CV joint fell apart as the set screws backed out and the pin fell out. I applied loctite to both set screws on each CV joint for both shafts.



The second problem proved more troublesome. I could not get the kingpin screws to go in straight so there was binding. I fiddled with it for a long time until I remembered the TTR shafts use a slightly thinner 3.5mm wide 8X16 bearing instead of the 4mm wide bearing (as included with the RC4WD kit). I swapped in a set of the thinner bearings and it all went together perfectly. I notified our team leader, who installed a set himself with no problems, so I'm not sure if this is a wide spread problem. But seeing as how these are cast parts I would think they are all the same, for the most part. Any way it is something future customers should be aware of.

But once I sorted everything out the assembly went well. The CV action is smooth and I can achieve the maximum steering throw in this TXT setup.



Installation: Clodbuster axles

I had initially thought I would do a quick install of the TXT axle and then install them in the test truck which is a race Clod. After running into problems with the TXT installation and knowing there might be problems with the race Clod because it has aluminum tubes and knuckles (I had to fidget around with them to get the TTR CVDs to work smoothly) I decided to try a more stock Clod axle to see if the knuckle issue was till present, it was.

I still had to use the 3.5mm bearings on the inside of the knuckles and I also had to tap on the Clod brass collars(the ones that are part of the differential assembly). I didn't have any issues with the TXT diffs but the brass collars took some effort to get on and off. In the end the axle came together and the XVDs operated as smoothly as they did in the TXT axle.




still more to come as I install the XVDs in my Clod race truck for durability test.....
hawnmt is offline   Reply With Quote
Sponsored Links
Old 06-16-2014, 02:59 PM   #2
I wanna be Dave
 
Join Date: Jan 2004
Location: Austin Texas
Posts: 3,788
Default Re: RC4WD Extreme Duty XVDS for Clodbuster and TXT review

Thanks for the review, it was very informative. I was curious to see how these would look!
Highmark is offline   Reply With Quote
Old 06-28-2014, 12:00 PM   #3
Newbie
 
Join Date: Apr 2012
Location: Manheim
Posts: 1
Default Re: RC4WD Extreme Duty XVDS for Clodbuster and TXT review

I also liked the review. I have a set of TTR cvd axles and stopped using them because the plastic hexes kept stipping, rounding. I thought about getting a set of rc4wd cvd axles but I found a place that make 12mm & 14mm aluminum hexes for the TTR axles. go here and take a look Hesse Machine he make other clod & txt1 parts.
j46da is offline   Reply With Quote
Old 06-28-2014, 01:12 PM   #4
Rock Crawler
 
Join Date: Apr 2007
Location: Hawaii
Posts: 708
Default Re: RC4WD Extreme Duty XVDS for Clodbuster and TXT review

Quote:
Originally Posted by j46da View Post
I also liked the review. I have a set of TTR cvd axles and stopped using them because the plastic hexes kept stipping, rounding. I thought about getting a set of rc4wd cvd axles but I found a place that make 12mm & 14mm aluminum hexes for the TTR axles. go here and take a look Hesse Machine he make other clod & txt1 parts.

Thanks!

Mike Hesse's products are all high quality, a lot of us use his parts on our trucks. He carries a good selection of custom Clod parts and I highly recommend them all.
hawnmt is offline   Reply With Quote
Old 05-09-2019, 04:10 AM   #5
Newbie
 
Join Date: Apr 2019
Location: PORT SAINT LUCIE
Posts: 31
Default Re: RC4WD Extreme Duty XVDS for Clodbuster and TXT review

Thanks for the review
gritsngreens1 is offline   Reply With Quote
Reply



RC4WD Extreme Duty XVDS for Clodbuster and TXT review - Similar Threads
Thread Thread Starter Forum Replies Last Post
RC4WD Extreme Duty XVDS for Clodbuster review hawnmt Tamiya Clod Buster 1 06-22-2014 11:33 PM
RC4WD's Extreme Duty XVD's for Axail Wraith are here AND IN STOCK Rckcrwlr Axial Wraith 17 02-01-2013 04:29 AM
*Giveaway* BWD FOFF Extreme Duty Motor Plate! billet works Formula Offroad 209 07-31-2011 06:50 PM
RC4WD Axial XVDs Testing!!! roborg5000 Axial AX-10 Scorpion 5 03-30-2009 05:49 PM
novak super duty extreme use question kobrajet428 Electronics 18 03-16-2007 09:45 PM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 05:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com