Go Back   RCCrawler Forums > Scale Rigs Brand Specific Tech > Tamiya Scale Rock Crawlers > Tamiya XC/CC01
Loading

Notices

Thread: cc-01 help

Reply
 
LinkBack Thread Tools Display Modes
Old 03-24-2012, 05:57 AM   #1
Quarry Creeper
 
Join Date: Jun 2006
Location: Tx
Posts: 198
Default cc-01 help

each time turn to the left right side drive shaft pops out wheels side



can anybody help me with this problem
wkxtreme is offline   Reply With Quote
Sponsored Links
Old 03-24-2012, 06:10 AM   #2
I wanna be Dave
 
Join Date: Aug 2008
Location: cape crud... will you be my friend
Posts: 2,073
Default

Is one of the shafts bent ?
crunky is offline   Reply With Quote
Old 03-24-2012, 08:00 AM   #3
Newbie
 
Join Date: Aug 2006
Location: vancouver, BC
Posts: 38
Default Re: cc-01 help

make sure there's an o-ring in each dogbone cup.
corycrawler is offline   Reply With Quote
Old 03-24-2012, 08:24 AM   #4
Quarry Creeper
 
Join Date: Aug 2010
Location: Brisbane Australia
Posts: 268
Default Re: cc-01 help

Replace with universals and that will never happen again.
rustykaos is offline   Reply With Quote
Old 03-24-2012, 09:23 AM   #5
Pebble Pounder
 
Join Date: Sep 2010
Location: Lees Summit
Posts: 190
Default Re: cc-01 help

Yep, both of those ^^^^

O-rings solved it for me, and then I got universals from ebay. No problems from either solution.
schiesz is offline   Reply With Quote
Old 03-24-2012, 09:21 PM   #6
Rock Crawler
 
Join Date: Dec 2011
Location: Las Vegas 89110
Posts: 585
Default Re: cc-01 help

you just proly forgot the rings like said above by others((((ring on each cup))).....ive run the snot out of cc-01s and never had the need for universals....you really only need universals if you shave and raise the front end...

my opinion though
greggreg2011 is offline   Reply With Quote
Old 03-24-2012, 10:44 PM   #7
Quarry Creeper
 
Join Date: Jun 2006
Location: Tx
Posts: 198
Default Re: cc-01 help

ill try the o-ring thing first plus i had rebend my drive shaft back
wkxtreme is offline   Reply With Quote
Old 03-25-2012, 05:34 AM   #8
Quarry Creeper
 
Join Date: Jun 2006
Location: Tx
Posts: 198
Default Re: cc-01 help

is it better have the o-rings on the chassis r the wheels side ???
wkxtreme is offline   Reply With Quote
Old 03-25-2012, 07:14 AM   #9
Quarry Creeper
 
Join Date: Feb 2008
Location: Oakdale, MN
Posts: 410
Default Re: cc-01 help

On the chassis side...
SFC K is offline   Reply With Quote
Old 03-25-2012, 07:25 PM   #10
Rock Crawler
 
Join Date: Dec 2011
Location: Las Vegas 89110
Posts: 585
Default Re: cc-01 help

spose to be both sides if i remember correctly...i built 2 in the last 4 mos but dont have them anymore so not 100 percent sure
greggreg2011 is offline   Reply With Quote
Old 03-25-2012, 07:35 PM   #11
Pebble Pounder
 
Join Date: Sep 2010
Location: Lees Summit
Posts: 190
Default Re: cc-01 help

I put 'em on both sides when I did it, worked like a charm.
schiesz is offline   Reply With Quote
Old 03-25-2012, 10:56 PM   #12
Quarry Creeper
 
Join Date: Feb 2008
Location: Oakdale, MN
Posts: 410
Default Re: cc-01 help

Yep, you can put them on both sides to be safe. I just looked in the manual and it is on the hub side. It does not calll for it on both.
SFC K is offline   Reply With Quote
Old 03-26-2012, 05:51 AM   #13
I wanna be Dave
 
Join Date: Nov 2009
Location: Houston
Posts: 2,004
Default Re: cc-01 help

On Tamiya kits when I'm too cheap to throw on universals/CVD's I usually take a bit of firm differential sponge and pack it into the diff output cup and put a rubber O ring on top. That way the dog bone has some room to move back and forth while still being snug without it flying out.

On the CC-01 you can't go wrong with the GPM CVD steering upgrade!
alexchen86 is offline   Reply With Quote
Old 03-28-2012, 10:02 PM   #14
Quarry Creeper
 
Join Date: Jun 2006
Location: Tx
Posts: 198
Default Re: cc-01 help

thanks for the help the o-ring help a lot for now no more drive shaft popping out for now
wkxtreme is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 01:45 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com