Re: Wheelbyte's Twin Hammers Upgraded the steering servo this week. As soon as I saw the Holmes Trailmaster BLS HV400 I knew this was the servo for me. The specs are very impressive. It is a huge improvement over the stock one.... night and day difference in speed and torque and thats running it with the weak built in BEC in the MMP. I plan to add a Castle 5amp BEC in the near future and bump up the voltage a bit. For now I am going to continue to run the stock shifting servo as I have had no problems with it. http://www.wheelbyte.com/b_board/TH16.jpg http://www.wheelbyte.com/b_board/TH17.jpg |
Re: Wheelbyte's Twin Hammers wheelbyte u inspired me to get a roc412 3100, this motor is amazing SOOO much power but i dont need to tell u that lol ty sir |
Re: Wheelbyte's Twin Hammers Added a few more things.....wife stoked me out on Vday and got me a Gift Certificate to RPP. :) MIP X-Duty driveshaft Vanquish RIGID INDUSTRIES 4" LED light bar Silver & mounts Vanquish caster blocks and steering knuckles http://www.wheelbyte.com/b_board/TH19.jpg http://www.wheelbyte.com/b_board/TH20.jpg |
Re: Wheelbyte's Twin Hammers This has to be one of the nicest TH on this site (or anywhere that I know of) and it keeps getting better. Just awesome! |
Re: Wheelbyte's Twin Hammers Very nice build! |
This is a sweet looking Hammer! Great job! |
Re: Wheelbyte's Twin Hammers Made it out and finished to my first RECON G6 this Sat at the Taters & Kilt event @ Rollins Lake. It was a blast!!! My rig made it through the 100+ gates with no breakage and the brushless setup with stock gearing I did it on 1 1/2 2200mAh 3s packs. I did notice in a few areas where even with the 500k diff fluid up front it was not enough.... next event I might try locking it up. I also gotta get my drag brake set up better. Other than that I was pretty happy on my rigs performance. http://www.wheelbyte.com/b_board/TH21.jpg http://www.wheelbyte.com/b_board/TH22.jpg http://www.wheelbyte.com/b_board/TH24.jpg |
Sweet Hammer my friend!!! I just got one myself. I ran it with my club yesterday for the first time. It did really well. Its a fun rig. This is Ford country, on a quiet night you can hear a Chevy rust. |
What size shock are you running next to the king shock. Sent from my DROID BIONIC using Tapatalk |
Re: Wheelbyte's Twin Hammers Quote:
|
Quote:
Sent from my XT1080 using Tapatalk |
Re: Wheelbyte's Twin Hammers Quote:
Thanks, yeah I am running 500k upfront right now and there were several times I needed more running the G6. Might have to switch back and forth depending on what type of event Im running fully locked for G6 where speed is not so critical and 500k for U4RC type events. |
Re: Wheelbyte's Twin Hammers Finally got around to installing the rear lights on my rig. They have been sitting in a box for a couple weeks. I used the HeyOK KOH lighting kit, EXO rear lightbar and a modified Carter Fab ultra 4 roof. Slid the entire roof about an inch forward, trimmed, rebent and redrilled to get the lights up higher and tuck them in closer. The blue and amber flash and the reds are brake lights. http://www.wheelbyte.com/b_board/TH25.jpg http://www.wheelbyte.com/b_board/TH26.jpg http://www.wheelbyte.com/b_board/TH27.jpg http://www.wheelbyte.com/b_board/TH28.jpg |
Did CFD do your hood also? I made 1 out of lexan kinda like it. |
Re: Wheelbyte's Twin Hammers Quote:
Yeah it is a Carter Fab hood but I cut the hole for the shock uprights. |
Re: Wheelbyte's Twin Hammers Ur rig u s one of the cleanest TH I have seen"thumbsup" |
Quote:
I also have 110 kings ( on my honcho ) I wish someone would make a new piston for them cas stock piston is horrible ( I have 60wt oil in them now and when you move the axle it feels like 15wt haha ) no tuning / dampening with stock piston ! They just look cool and I'm kinda over that , I want them to perform ! Sent from my iPad using Tapatalk |
Re: Wheelbyte's Twin Hammers Quote:
Yeah I hear ya I am running 100wt in my Kings to get some dampening out of them.... bleeding them is also a PITA. I wish they were built like the Proline Powerstrokes with a diaphram and bleeder hole. I did notice they now also make a short course version of the Kings that are bigger in dia. wonder if anyone has tried them out and how they perform. |
I don't think they changed the piston ( I could be wrong ) .. Looks like they just changed springs..... I have the extra spring kit.... Don't matter what springs I put on the pistons are useless... Haha Sent from my iPhone using Tapatalk |
Re: Wheelbyte's Twin Hammers Quote:
110mm Kings w Piggyback
110mm Short Course Kings
|
All times are GMT -6. The time now is 02:14 AM. |
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com