• Welcome to RCCrawler Forums.

    It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!

    Already a member? Login at the top of this page to stop seeing this message.

Cordless Screwdriver

I use the Dewalt 8V posted earlier. There is no clutch, but I don't trust a clutch on plastic. The inline allows me to hand tighten the final amount almost like a normal driver (still a bit bulky).

I got it as a refurb for around $40.
 
I also wouldn't typically trust a clutch when going into plastic but that's why I like the $14 HyperTech 4.0vt. Even on the 2nd or 3rd setting it will start ratcheting when it meets resistance. On the 1st setting there's no way even on soft plastics that it's going to keep spinning. To do anything around the house... even just drilling into drywall, I have to ramp the clutch way up to keep it going.
 
I picked up the 8v pistol grip about eight months ago and use it all the time. I find the control to be pretty responsive and sensitive and I like the ability to change the configuration. It’s not cheap but I’m happy with it and hope to never have to replace it. I almost bought the Milwaukee that was mentioned earlier in the thread but ended up going with this because of the versatility. My only complaint is that I wish it had a chuck and I’m sure there’s add-ons if I ever get around to it.

https://www.homedepot.com/p/DEWALT-...uczk6nLiV0489UiqDO0aApnGEALw_wcB&gclsrc=aw.ds
 
high plains drifter said:
I also wouldn't typically trust a clutch when going into plastic but that's why I like the $14 HyperTech 4.0vt.
Click to expand...

I use one as well. Not too much power so it can strip out, just enough to get the job done. Clutch is very accurate too. Works great!

I picked up several 2mm, 2.5mm, and 1/16" bits, both short and long. I also picked up a couple of manual handles so I can swap bits between the manual handle and the power driver. Works fantastic, and consolidated many of my tools. "thumbsup"
 
Let’s just say I went to the shed and upgraded lmao

9b0f9d1d5243fc9c3de564a068dcb1f4.jpg


After using this, I don’t want to use anything else.

It’s speed really helps on the portal boxes for example.

Obviously you have to hand tighten it down, but it’s still a lot faster. [emoji1690]


Sent from my iPad using Tapatalk
 
I happened to browse through this thread and decided to buy the Hyper Tough screw driver from Walmart, as recommended by some people in this thread. While I can't say what the exact torque it delivers at the lowest clutch setting, I do think it's a reasonable amount of torque suitable for M3 self tapping screws or machine thread screws commonly used in 1/10 RC builds. It seems to be a great value for the price. Has 2 years warranty so I hope it's durable. I am keeping my receipt just in case : )
 
usert_l said:
I happened to browse through this thread and decided to buy the Hyper Tough screw driver from Walmart, as recommended by some people in this thread. While I can't say what the exact torque it delivers at the lowest clutch setting, I do think it's a reasonable amount of torque suitable for M3 self tapping screws or machine thread screws commonly used in 1/10 RC builds. It seems to be a great value for the price. Has 2 years warranty so I hope it's durable. I am keeping my receipt just in case : )
Click to expand...


Good to hear it is good so far! I was curious in that drill.


Sent from my iPad using Tapatalk
 
high plains drifter said:
I also wouldn't typically trust a clutch when going into plastic but that's why I like the $14 HyperTech 4.0vt. Even on the 2nd or 3rd setting it will start ratcheting when it meets resistance. On the 1st setting there's no way even on soft plastics that it's going to keep spinning. To do anything around the house... even just drilling into drywall, I have to ramp the clutch way up to keep it going.
Click to expand...

SOLD! I just ordered one. Heck, for $14 bucks I'll give it a try!! Thanks for the recommendation.
 
OSRC said:
I use one as well. Not too much power so it can strip out, just enough to get the job done. Clutch is very accurate too. Works great!

I picked up several 2mm, 2.5mm, and 1/16" bits, both short and long. I also picked up a couple of manual handles so I can swap bits between the manual handle and the power driver. Works fantastic, and consolidated many of my tools. "thumbsup"
Click to expand...

I've using the Hyper Tough 4v from Walmart for a month now. It works very well, and as other have said the clutch is effective. The LED light is helpful and the battery lasts a LONG time. Best 14 bucks tool I've ever bought!
 
JimInMiami said:
I've using the Hyper Tough 4v from Walmart for a month now. It works very well, and as other have said the clutch is effective. The LED light is helpful and the battery lasts a LONG time. Best 14 bucks tool I've ever bought!
Click to expand...


Really glad to hear it's working for you. I've been surprised how much I'm using it for other tasks around the house but I've grown very comfortable with it at this point... knowing where to set the clutch for various jobs and being able to rely upon it to not over-tighten or strip various materials.
 
You must log in or register to reply here.

Similar threads

U
FMS 1:12 Land Rover Series II (SWB)
Replies
4
Views
2K
snowmanf
S
high plains drifter
Resurrecting a 25 year old RC10 GT
2 3
Replies
59
Views
3K
svt923
S
soze
Soze's Element Enduro Knightrunner Build
Replies
17
Views
4K
soze
soze
JatoTheRipper
Vanquish VRD Stance RTR
2
Replies
33
Views
7K
Col_Sanders
Col_Sanders
T
Wratih Spawn 5K Kit Build The Last NIB Wraith Kit?
Replies
13
Views
2K
Goro Majima
G
Back
Top