dshelowjr
Quarry Creeper
I'll bring the thermocell with me . Then we shall have no more skeeters"thumbsup" We might even go pick up another one tomorrow . We can set one at each course.
-
Welcome to RCCrawler Forums.
It looks like you're enjoying RCCrawler's Forums but haven't created an account yet. Why not take a minute to register for your own free account now? As a member you get free access to all of our forums and posts plus the ability to post your own messages, communicate directly with other members, and much more. Register now!
Already a member? Login at the top of this page to stop seeing this message.
SSRCC Comp #3 - June 5 - Gainesville
- Thread starter Scattman
- Start date
Scattman
Official Cook of the ECC
Had to buy the servo. the rest was freeThe servo was so I could put the 5955 on the 1.9:twisted: I really like 486 oz of torque"thumbsup"
It's like a different rig every time you comp with it. Wait........it is a different rig every time you comp with it.
dshelowjr
Quarry Creeper
At least it's built when I get thereIt's like a different rig every time you comp with it. Wait........it is a different rig every time you comp with it.
It will continue to be a different rig until I'm happy with it.
DickyT
I wanna be Dave
Wade is bringing his propane powered bug killer too, supposed to be good for up to an acre. "thumbsup"I got 100% DEET bug juice that anyone with out is welcome to use too.
Tydl
RCC Addict
one more day!
Scattman
Official Cook of the ECC
I might go out today and try to clean up the rocks a bit. Slicker than owl poop out there with all this rain.
DickyT
I wanna be Dave
Kenny, I have 2 used rovers already packed up for you. I never got around to swapping my rears, so only 2.
David, I have the weight retaining screws packed for you as well.
Meeting up with Wade in about 3 hours to head north! "thumbsup"
David, I have the weight retaining screws packed for you as well.
Meeting up with Wade in about 3 hours to head north! "thumbsup"
Scattman
Official Cook of the ECC
Bring some tennis shoes or sneakers or something guys. There will be some climbing of rocks involved and they are slick. You'll see what I mean when you get out there.
Donnie, Kinson and I may head out after the comp and check a new spot out.
Donnie, Kinson and I may head out after the comp and check a new spot out.
DickyT
I wanna be Dave
Kenny, I am bringing my new rovers with me, after the comp if time allows I will pull the other set off the truck and you can have them too.
I just do not want to run an unsiped, brand new rover "thumbsup"
I just do not want to run an unsiped, brand new rover "thumbsup"
Scattman
Official Cook of the ECC
You guys should to get ahold of me when you get to town. I should be in town by then.
There is a Hobbytown USA right down the street from the comp spot. You will go right by it.
There is a Hobbytown USA right down the street from the comp spot. You will go right by it.
DickyT
I wanna be Dave
We do not have your number or we would get a hold of you when we get to town"thumbsup"
We are delayed an hour getting on the road, Wades service call ran long.
I'll pm you my #, send me a text with yours.
DickyT
I wanna be Dave
Leaving now to pick up a thermacell (more can't hurt), drive to Wade's then hit the road.
On the road again, just can't wait to get on the road again...
Matt, see my 2nd pm for correct info. my dyslexia got the better of me on the 1st.
I packed my HK USP BB Pistol too to ward off angry hoards of rabid squirrels :lmao:
On the road again, just can't wait to get on the road again...
Matt, see my 2nd pm for correct info. my dyslexia got the better of me on the 1st.
I packed my HK USP BB Pistol too to ward off angry hoards of rabid squirrels :lmao:
Scattman
Official Cook of the ECC
Finally replaced that bent shock shaft and worked on the suspension some. Ran on my test pile out back and am very pleased with the results. Freed up the suspension some and no more hanging a tire in the air.
Getting ready to start switching my 3rd channel button over to where I can actually reach it. "thumbsup"
Next will be to install the 22 turn 550 size motor in the scaler for some 3S fun this weekend.
Getting ready to start switching my 3rd channel button over to where I can actually reach it. "thumbsup"
Next will be to install the 22 turn 550 size motor in the scaler for some 3S fun this weekend.
Scattman
Official Cook of the ECC
Scaler is done."thumbsup" Who all is bringing their scalers?
I will wait and do the radio mod tonight along with my secret mods that I want to premier tomorrow. ;-)
I will wait and do the radio mod tonight along with my secret mods that I want to premier tomorrow. ;-)
Last edited:
Kinson
Pebble Pounder
wow my rig is still in the truck from last weekend, I guess it will work tomorrow. :lmao:
hope to make it up for my first crawl with a stock ax10. If am late does that matter? Have an early morning appointment that could run long.
RSVP:
1. Scattman
2. Mini
3. Speedracer19
4. Kennyj
5. Dshelowjr
6. Dickyt
7. Tydl (wade) Look-betcha middle of the pack!
8. Kevin
9. Juan
10. Woody(probably use my rig)
11. Kinson
12. Brian
13. billj
14. rich
15. rocktime
16. Allen
RSVP:
1. Scattman
2. Mini
3. Speedracer19
4. Kennyj
5. Dshelowjr
6. Dickyt
7. Tydl (wade) Look-betcha middle of the pack!
8. Kevin
9. Juan
10. Woody(probably use my rig)
11. Kinson
12. Brian
13. billj
14. rich
15. rocktime
16. Allen
