Rowdys XR, BJV4, SA, Now Team Y-Town "Double Agent"

[ROWDY RACING]

Axial Ti gear shafts showed up today. My VP motor plates should be here tomorrow. They will both join my VP trans cases to hopefully put my VP-10 a little closer to being bullet proof.

[sally1800]

where did you get those?

[ROWDY RACING]

Originally Posted by saydee1800

where did you get those?

ckrc

[Jeepkid]

Originally Posted by ROWDY RACING

I never did the 9mm mod, I glued my bearings in tight and knock on wood I have not had any problems. I have the VP trans cases and they really smoothed the drivetrain out. I ordered the VP motor plates yesterday, so that should solve the bearing issues. I would say get the VP motor plates they are $20 and come with upgraded bearings.

When I gotmy XR I loctited the stock bearings in. Waited for my punkdig, and then did the 9mil mod b4 the dig showed. What bitch to get them bearings out of the plates with loctite holding them in there. It seems it takes the slop out, but you got your VP bling on its way.

[ROWDY RACING]

Yea I got the Axial stage 2 carbon fiber kit, and some Axial black springs also but I have to wait for the old lady to give them to me for Christmas!

[Jeepkid]

Oh,my wife told me to order the stuff I wanted yesterday. To bad she said my limit was 40bucks. I got VP plates and cases.

[ROWDY RACING]

Some more VP sweetness showed up today. Time to rebuild the trannies with these and Ti shafts!

[ynmech]

I like the battery mount

[ROWDY RACING]

Originally Posted by ynmech

I like the battery mount

Thanks!

I rebuilt the rear trans last night with the VP motor plate and Axial Ti shaft to go along with the VP trans case. I have been running stock bearings since day one and had no problems, but I found a busted one during the tear down. All of the gears were fine so all is good. The rear axle is butter smooth now and I can't wait to do the front axle tonight.

[ROWDY RACING]

Chalked up another victory with the XR yesterday. I love it more everytime I drive it. I had Losi gold springs on the front and Axial blacks on the rear. I am going to add Axial blacks up front also, I like the feel of a super soft suspension. I also have a new lid coming from Rockthrasher.
Carbon fiber Hardline for ROWDY RACING

[ROWDY RACING]

Well she now has Axial black springs all around, Axial CF chassis, and servo mounts. I also got the Axial aluminum shock caps and pre-load adjusters used from firekiddco2.

[greenjeeper92]

servo plate

[ROWDY RACING]

Took her out for some testing yesterday. I can't really say I noticed much difference with the new setup good or bad. Since I did'nt notice any negative effects with the changes I guess I will stick with it for now.

[Harvo]

Nice job. Where did you buy your Axial black springs?

Thanks

[ROWDY RACING]

Originally Posted by Harvo

Nice job. Where did you buy your Axial black springs?

Thanks

I believe at the time I purchased them CKRC was the only place that had them in stock.

[crawldad91]

that vp10 looks nice!;) would be interested in finding out where you can get a set of them high clearance delrin lowers

[ROWDY RACING]

Originally Posted by crawldad91

that vp10 looks nice!;) would be interested in finding out where you can get a set of them high clearance delrin lowers

The delrin lowers are T1E, you can get them at www.T1Erc.com.

[ROWDY RACING]

Originally Posted by greenjeeper92

servo plate

Good eye, I put one on here to test out. I used to run one on my AX-10.

[MRCCRAWLER1.9]

man thats a sick servo plate.

[ROWDY RACING]

Originally Posted by MRCCRAWLER1.9

man thats a sick servo plate.

Thanks, yea most servo protectors I have seen offer zero protection for the front of the servo. The front of the servo is what takes the beating, so I think it's more important to cover the front than the top.