| |
| |||||||
 |
| | LinkBack | Thread Tools | Display Modes |
11-19-2015, 09:44 AM
| #1 |
| Rock Stacker Join Date: Nov 2015 Location: Lubbock
Posts: 95
| 
So I'v just about finished up putting the front suspension together last night but notices that the stock settings seems to incorporate quite a bit of negative camber. I know that I can make adjustments to correct this but wanted to make sure I didn't something backwards or upside down.  both sides came out the same and I used a caliber to measure length.  Last edited by THX_138; 11-20-2015 at 11:41 PM. |
|  |
| Sponsored Links | |
| | |
|
11-19-2015, 09:46 AM
| #2 |
| RCC Addict Join Date: Aug 2012 Location: Philippines
Posts: 1,652
| Re: Negative Camber with stock settings
Put the camber link on the inner hole of the caster block, not the outer one.
|
|
| |
|
11-19-2015, 09:49 AM
| #3 | |
| RCC Addict Join Date: Mar 2012 Location: Under a Rock in North Texas
Posts: 1,389
| Re: Negative Camber with stock settings Quote:
| |
|
| |
|
11-19-2015, 09:52 AM
| #4 |
| Rock Stacker Join Date: Nov 2015 Location: Lubbock
Posts: 95
| Re: Negative Camber with stock settings
That's what I thought too gbean but the instructions showed the outer hole for stock setup so I thought maybe I had something else off. Would have hated having it all built up just to realize I have to tear it down to flip a part. Figured it would be easier to ask at this stage then later. I'll make the changes tonight.
|
|
| |
|
11-19-2015, 09:53 AM
| #5 |
| RCC Addict Join Date: Aug 2012 Location: Philippines
Posts: 1,652
| Re: Negative Camber with stock settings
What position is the inboard end on?
|
|
| |
|
11-19-2015, 09:59 AM
| #6 |
| Rock Stacker Join Date: Nov 2015 Location: Lubbock
Posts: 95
| Re: Negative Camber with stock settings
I want to say bottom outside
|
|
| |
|
11-19-2015, 11:13 AM
| #7 |
| Quarry Creeper Join Date: Feb 2011 Location: Nevada
Posts: 302
| Re: Negative Camber with stock settings
When I followed the instructions I got the same results. I used my RPM camber gauge and lengthened the link. The instructions were not 100% correct. Seems there was another mistake in the instructions, but I can't recall right now. |
|
| |
|
11-19-2015, 12:10 PM
| #8 | |
| RCC Addict Join Date: Aug 2012 Location: Philippines
Posts: 1,652
| Re: Negative Camber with stock settings Quote:
| |
|
| |
|
11-19-2015, 01:11 PM
| #9 | |
| Rock Stacker Join Date: Nov 2015 Location: Lubbock
Posts: 95
| Re: Negative Camber with stock settings Quote:
| |
|
| |
|
11-19-2015, 05:00 PM
| #10 |
| Pebble Pounder Join Date: Dec 2014 Location: Duluth
Posts: 114
| Re: Negative Camber with stock settings
Double check the latest online download of the instructions. there were were several issues when it cames to link dimensions and grease locations. I know I went through my book and redlined everything to match.
|
|
| |
|
Negative Camber with stock settings - Similar Threads | ||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Hobbywing stock combo esc settings | Mick0004 | Electronics | 4 | 04-19-2015 10:17 PM |
| Installed asiatees c hubs, now my camber is negative? | woodsman541 | Newbie General | 18 | 03-13-2015 07:17 AM |
| Stock low voltage cutoff settings | P-J | Axial Yeti | 6 | 02-05-2015 11:28 PM |
| Stock ESC settings | tcm glx | Axial Wraith | 5 | 02-09-2013 09:18 PM |
| Rear negative camber? | frdtrkguy | General Crawlers | 1 | 12-30-2007 09:30 AM |
| Thread Tools | |
| Display Modes | |
| |
Linear Mode
