Go Back   RCCrawler Forums > Vendors > Vendors Market > Axles, Trannys, T-case
Loading

Notices

Thread: BmachineRC Splined "Repair" tubes

Reply
 
LinkBack Thread Tools Display Modes
Old 11-25-2013, 05:43 AM   #1
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle





BmachineRC Will Be Closed For A Few Months!!!
Ive been at this for 2 or 3 years now and have had a blast making parts for the RcCrawler community.
Thank you !!!
But unfortunatlly in that time I have gotten behind in other aspects of my life that I need to catch up on.
If I have a chance to make any parts during my break, I will post them up.
Thanks again to everyone who has used any of my products!!!


SPLINED 7075 AX10 HOUSING TUBES






Have an old housing with the ends snapped off...These are the tubes for YOU!






Designed to use VP XR10 C-hubs





THESE TUBES WILL BE OFFERED 2 WAYS:


#1...REPAIR TUBES...$55.00 shipped
Drilled and Tapped for VP C-Hub
( you will have to trim housing and drill and tap holes to mount in housing)


#2...Tubes PRE - INSTALLED IN NEW HOUSING...$75.00 shipped
(while housing supplies last)


UPDATE: These tubes will work on the rear using XR10 VP lockouts and XR10 short side axle shafts with no mods...you only get .100 engagement into the locker.
Long side shafts milled down is a better option.


My Paypal is : BmachineRC@gmail.com


Please include which option you want in the PayPal notes
Please include RCCrawler screen name in the PayPal notes
__________________________

"STOCK SCX10 WIDTH AXLE TUBES
USING VP WRAITH KNUCKLES"

__________________________

** Want more steering on your SCX10 axle? **

** Been holding back on doing the XR / Wraith mod
because you don't want your front axle wider than your rear? **

** This may be what your looking for. **




7075 Spline tube with machined VP Chubs





XR Universals With Re-Machined Tangs



The Options :

SCX 10 Tubes Only.... $48.00

Tubes with new VP C-Hubs.... $100.00 (Your choice of VP color)

Tubes with New VP C-Hubs installed in New AX 10 housing.... $128.00

XR 10 axles with Machined Tangs.... $48.00

Wraith Knuckles.... $40.00

( shipping times will vary based on non BmachineRC parts availability)
(pricing may vary based on a lot of things)

Thanks for looking

My Paypal is : BmachineRC@gmail.com


Please include which option you want in the PayPal notes
Please include RCCrawler screen name in the PayPal notes

Last edited by BDN; 08-13-2016 at 04:11 PM. Reason: added stuff
BDN is offline   Reply With Quote
Sponsored Links
Old 11-25-2013, 06:37 AM   #2
I wanna be Dave
 
Join Date: Oct 2008
Location: Sumter
Posts: 6,141
Default Re: BmachineRC Splined "Repair" tubes

Great work on these Bruce! Having the option to pick up the housing already modified should be a great service to take some of the anxiety out of getting things set up correctly and not botching the threads the first time around.

ittybitty is offline   Reply With Quote
Old 11-25-2013, 07:10 AM   #3
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

Quote:
Originally Posted by ittybitty View Post
Great work on these Bruce! Having the option to pick up the housing already modified should be a great service to take some of the anxiety out of getting things set up correctly and not botching the threads the first time around.

Thanks Ryan,
I know there are a couple other splined tube tubes out there, but it's always nice to have options
BDN is offline   Reply With Quote
Old 02-24-2014, 03:39 PM   #4
RCC Addict
 
Join Date: Nov 2007
Location: somewhere
Posts: 1,403
Default Re: BmachineRC Splined "Repair" tubes

Those r nice looking Bruce keep me in mind when I go to build a sporty lol
lowridinjuggalo is offline   Reply With Quote
Old 02-24-2014, 04:07 PM   #5
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

Quote:
Originally Posted by lowridinjuggalo View Post
Those r nice looking Bruce keep me in mind when I go to build a sporty lol
Thanks Marcus...Get going on that sporty build
BDN is offline   Reply With Quote
Old 02-24-2014, 04:11 PM   #6
RCC Addict
 
Join Date: Nov 2007
Location: somewhere
Posts: 1,403
Default Re: BmachineRC Splined "Repair" tubes

Gotta finish the pro first just pick up a awesome chassis from u sat need a lil more time lol
lowridinjuggalo is offline   Reply With Quote
Old 02-24-2014, 04:14 PM   #7
Rock Crawler
 
Join Date: Jul 2005
Location: Spartanburg
Posts: 861
Default Re: BmachineRC Splined "Repair" tubes

I spoke with M_ENERGY about these on Sunday! I am impressed!
2003EDGE is offline   Reply With Quote
Old 02-27-2014, 05:16 PM   #8
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

Thank you sir. The ones Derrick and BIGJON have put a hole new twist on things
BDN is offline   Reply With Quote
Old 10-18-2014, 07:07 AM   #9
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

"True" SCX 10 Width Axle added to post
BDN is offline   Reply With Quote
Old 11-20-2014, 04:02 AM   #10
Rock Stacker
 
Join Date: Jan 2007
Location: Carson City
Posts: 68
Default Re: BmachineRC Splined "Repair" tubes

Do you have any of the SCX10 width splined tubes instock ???
Baddawg775 is offline   Reply With Quote
Old 11-20-2014, 05:48 AM   #11
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

Quote:
Originally Posted by Baddawg775 View Post
Do you have any of the SCX10 width splined tubes instock ???
PM sent
BDN is offline   Reply With Quote
Old 12-03-2014, 04:14 PM   #12
Rock Stacker
 
Join Date: Jan 2007
Location: Carson City
Posts: 68
Default Re: BmachineRC Splined "Repair" tubes

Brian, my splined tube & axle housing just arrived today !!!
Looks great, can't wait to finish assembling them. Thanks !!!
Baddawg775 is offline   Reply With Quote
Old 12-03-2014, 04:30 PM   #13
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes

Quote:
Originally Posted by Baddawg775 View Post
Brian, my splined tube & axle housing just arrived today !!!
Looks great, can't wait to finish assembling them. Thanks !!!
Thanks Chip...Post up some pic's when you get it built
BDN is offline   Reply With Quote
Old 12-10-2014, 06:49 PM   #14
Rock Stacker
 
Join Date: Jul 2010
Location: State of Jefferson
Posts: 86
Default Re: BmachineRC Splined "Repair" tubes

I have to say that Bruce has an incredible product here. The one reason that I've waited on doing this mod is because I wanted the front axle to match the width of the rear axle. This set-up is spot on and is beefy as heck. For the axles, I went with new Vanquish VVD's. Vanquish did a set for me that has the SCX-10 axle shafts with Wraith stubs. With the new shafts in hand, I had to extend the axle flats 6mm and trim 5mm (could have trimmed only 4mm) off the ends. At full turn, I have 3-4mm clearance between the wheels and shocks (stock) so no rubbing there. Thanks Bruce for you help and advice. So on to the pictures.
Attached Images
      

Last edited by Adama; 12-10-2014 at 07:00 PM.
Adama is offline   Reply With Quote
Old 01-20-2015, 08:43 PM   #15
Rock Stacker
 
Join Date: Dec 2011
Location: Apache Junction
Posts: 96
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

Any chance on there ever being a metal version available at all? I like the idea of a metal version of the Repair Tubes to add a lil bit more weight to the axles than the aluminum version and the whole metal threads being way stronger than aluminum would be sick too!
isac is offline   Reply With Quote
Old 01-21-2015, 06:01 AM   #16
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

Quote:
Originally Posted by isac View Post
Any chance on there ever being a metal version available at all? I like the idea of a metal version of the Repair Tubes to add a lil bit more weight to the axles than the aluminum version and the whole metal threads being way stronger than aluminum would be sick too!
I have actually been working on steel tubes
BDN is offline   Reply With Quote
Old 01-21-2015, 10:50 AM   #17
I wanna be Dave
 
Join Date: Jan 2012
Location: williamsport
Posts: 8,582
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

New axle showed up yesterday!

BND of BmachineRC did an Incredible job executing this axle setup!

When I did the rear steer on my scx, I realized that the narrow XR mod still left a gain in track width.
So when I saw the True width "repair" tubes from Bruce, I knew it had to be my new front axle!

I sent a Dlux modded scx housing and a VP wraith C's to Bruce and let him do his work.



I used as many vendor parts as I could.. Dlux modded scx housing, BmachineRC "repair" tubes, and a HH torquemaster spool.



It all fits beautifully with the "repair" tubes!

winnerone23 is offline   Reply With Quote
Old 01-22-2015, 03:20 AM   #18
Rock Crawler
 
Join Date: Oct 2011
Location: Fairfield
Posts: 650
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

Bruce, do you do normal width xr shafts (the regular xr mod on the scx10 housing which is a hair wider than scx10 but narrower than XR) looking to run a press fit style locker and the tangs are very difficult to get nice and square while keeping the press fit size.

Thanks, Ben
802coma is offline   Reply With Quote
Old 03-18-2015, 08:06 PM   #19
I wanna be Dave
 
Join Date: Jan 2012
Location: williamsport
Posts: 8,582
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

Quote:
Originally Posted by 802coma View Post
Bruce, do you do normal width xr shafts (the regular xr mod on the scx10 housing which is a hair wider than scx10 but narrower than XR) looking to run a press fit style locker and the tangs are very difficult to get nice and square while keeping the press fit size.

Thanks, Ben
Bruce does offer tang services..

I've been running this front axle setup and have absolutely loved it! Well worth the performance gain on this mod!
winnerone23 is offline   Reply With Quote
Old 03-19-2015, 10:40 AM   #20
BDN
Quarry Creeper
 
Join Date: Dec 2011
Location: Us
Posts: 317
Default Re: BmachineRC Splined "Repair" tubes and "True" SCX 10 Width Axle

Quote:
Originally Posted by 802coma View Post
Bruce, do you do normal width xr shafts (the regular xr mod on the scx10 housing which is a hair wider than scx10 but narrower than XR) looking to run a press fit style locker and the tangs are very difficult to get nice and square while keeping the press fit size.

Thanks, Ben
Pm sent
BDN is offline   Reply With Quote
Reply



BmachineRC Splined "Repair" tubes - Similar Threads
Thread Thread Starter Forum Replies Last Post
BmachineRC Splined "Repair" tubes BDN New Products and Great Deals 0 11-24-2013 05:45 PM
<iframe width="420" height="315" src="//www.youtube.com/embed/gYr-dbPEOnE" frameborde boolean21 Scale Videos! 0 10-01-2013 09:39 AM
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -6. The time now is 05:53 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
Copyright 2004-2014 RCCrawler.com